Aulitzky Exhaust | Race rear silencer / exhaust system 3” (76mm) Straight-Pipe | fits Ferrari F8 Tributo/Spider 721hp | Motorsport articles

MOVIT DDE steel brake system 370x35mm (6 piston calliper) for the front axle, from 18 inch rims upwardsApplication-focussed development is the cornerstone of this high-performance brake system. The required balance of weight, performance and durability is optimally combined. The uncompromising selection of materials in production results in a highly unique product that meets the diverse requirements of extreme automotive applications. The most important features of the MOVIT brake system are- The progressive staggering of the piston diameters, matched to the vehicle, so that precisely parallel contact pressure between the pad and the disc is guaranteed. This enables even wear of the brake pads and ensures even heat transfer and a reduced system temperature.- Very good heat dissipation due to the open design of the brake pad contour.- Calipers manufactured from high-strength, highly tempered aircraft aluminium 7075 with high-quality material properties (stiffer components, more homogeneous structure), hard anodised and coated with a triple paint finish.- Optimised stability due to the length of the callipers- Larger brake disc diameter and thickness, more cross holes (each pre-cast hole is re-drilled and countersunk, which has a favourable effect on the flow).- The brake discs are thermally tempered.- The optimised DDE ventilation system (double directional evolvent system) of the brake disc has an 80% larger surface area compared to other brake discs, the temperature of the brake disc is significantly reduced and therefore also the wear.- Long service life of the wearing parts, excellent response behaviour, steel flex lines ensure consistent performance.- Optimally matched brake pads ensure fading resistance, a long service life and reduced wear on spare parts Attention: The conversion means that only rims with at least 18 inches can be fitted! The chassis number of the vehicle on which the brakes are fitted is required for the parts certificate. MOVIT sports brake callipers, 6s5, 6-piston- Milled from high-strength aircraft aluminium 7075- Two-piece- Use of maximum disc size due to long design- Significantly improved rigidity and extended contact surface of the pad- Uniform heat transfer- Reduced system temperature- Low, even pad wear- Progressive piston staggering- Crown system for fixing the brake hose- RAPAD-X system for quick brake pad replacement without removing the caliper from the bracket- Open brake pad track for optimised cooling- Maximum stability- Maximum braking force MOVIT sports brake discs, 370x35mm, 2-piece- Highly efficient DDE cooling system- Perforated for optimum response behaviour even on wet roads- Maximum fading resistance- Special alloy for high thermal conductivity MOVIT comfort brake pads, BE-6s1- Enlarged friction surface- Lower system temperature- Uniform heat transfer- Longer service life Scope of delivery:2x MOVIT brake caliper (left/right)2x MOVIT brake disc (left/right)2x vehicle-specific brake caliper adapter1x set of comfort brake pads2x steel flex lines1x assembly material1x installation instructions and running-in instructions1x parts certificate Compatible vehicles:BMW 1 Series F20 / F21 (also M)Ford Focus RS CB4 / MKIIAudi RS3 8PAudi RS4 B5Audi S4 Type 8D / B5BMW M3 E46BMW M3 E46 CSLBMW M3 E92Ford Mustang V Shelby GT 500Mercedes Benz W639 Vito / VianoVolvo XC90 1st gen. from 2011 onwardsVW Golf VII GTI / GTD 57 series pistonsVW Golf VII GTI / GTD 57 series pistonsVW GOLF VII GTI Clubsport / Performance 60 series pistonsVW Golf VII RVW Golf VII RVW T5 / T6 Multivan

Facts:Performance increase: 15-20hpExpert opinion: withoutManufacturer: EventuriMaterial: CarbonExpert opinion: without The Mercedes A35 AMG Eventuri intake system was developed to provide the turbo with a less restrictive flow path while keeping intake temperatures low. Reducing heat suction and increasing internal volume are the main considerations when developing an intake system for turbocharged engines. In the A35, the intake system is located in close proximity to the exhaust manifold, which quickly heats up the engine compartment. High temperatures have a detrimental effect on engine performance, as the turbo has to build up boost pressure with heated, less dense air. Therefore, the only way to reduce IAT to a minimum is to have a completely sealed intake tract. To reduce the restrictions of a closed intake tract, we increased the volume of the airbox by relocating the ECU and providing an opening in the airbox on the cold side, away from the direct heat of the manifold. The carbon inlet pipe has a larger internal volume with an initial internal diameter of 111mm (4.4?) which tapers smoothly to match the turbo inlet pipe diameter. Finally, we use a custom high-flow dry filter that is ISO approved and has a larger filter area than the stock filter. Dyno testsThe dyno tests were carried out by MSL Performance, a Mercedes specialist based in the UK. A fully standard A35 AMG was tested with the standard airbox and then with the Eventuri intake system, with the same external conditions. As can be seen below, the intake system offers an increase in power throughout the rev range. The highlighted point shows a significant power gain as the intake allows a higher flow rate in the higher rev range where the stock airbox becomes a restriction. The resulting performance gains are noticeable on the road, with better throttle response and improved acceleration times. With a tuned A35 we would expect even better gains as the demand from the turbo increases. The Eventuri A35 intake system consists of a number of components designed for a specific purpose and manufactured to the highest standards. We use 100% pre-impregnated carbon fiber without fiberglass, which means we can achieve a smooth inner surface to get a smoother airflow. Here are the details for each component and the design ethos behind them: Each intake system consists of:Carbon airboxCustom high-flow dry-cone filterCarbon intake tubeCNC-machined intake flangeLaser-cut stainless steel brackets and ECU coverSilicone coupler with OEM clamps Compatible vehicles:VehicleVehicle typePowerEngine capacityEngine typeYear of construction Mercedes A-Klasse (W177/V177)A250 / 4-matic165kW / 224hp1991cm³M 260.92003.18 - Mercedes A-Klasse (W177/V177)A35 AMG 4-matic225kW / 306hp1991cm³M 260.92009.18 - Mercedes CLA (C118/X118)A250 / 4-matic165kW / 224hp1991cm³M 260.92003.19 - Mercedes CLA (C118/X118)CLA35 AMG 4-matic225kW / 306hp1991cm³M 260.92004.19 - Mercedes GLB (X247)GLB250 / 4-matic165kW / 224hp1991cm³M 260.92008.19 - Mercedes GLB (X247)GLB35 AMG 4-matic225kW / 306hp1991cm³M 260.92008.19 -

Facts:Material: CarbonManufacturer: EventuriParts certificate: A certificate is available for this product for certain regions and vehicles (details below) Introducing our E9X carbon fiber air collector. Made from 100% high quality prepreg carbon including the inner trumpets, this air collector replaces the stock plastic version and unleashes the roar of the naturally aspirated V8 engine.As the trumpet lengths are tuned to the inner volume, changing this setting can result in a loss of power, so we have kept the same volume so as not to affect the way the car drives in terms of power delivery. Although there is no performance gain from the carbon plenum, the intake noise produced takes the driving experience to a whole new level. We went through several iterations with different material thicknesses to fine tune the sound, and the resulting plenum produces an almost unbelievable intake sound! This plenum can be used with the OEM airbox or any other aftermarket intake system, including our own Eventuri intake systems for a real performance boost. Parts certificateThe manufacturer's specifications apply to installation. An existing certificate is no guarantee that the product can also be installed in the corresponding vehicle. A certificate is available for this product for the following regions and vehicles:* DE/AT: Vehicle registration document, field K --- CH/LI: Vehicle registration document, field 24Country model type approval*DE/AT BMW E90 M3 e1*2007/46*0377*..DE/AT BMW E92 M3 e1*2007/46*0377*..DE/AT BMW E93 M3 e1*2007/46*0377*..DE/AT BMW GTS e1*KS07/46*0012*..DE/AT BMW M3 e1*2001/116*0345*.. Compatible vehicles:VehicleVehicle typePowerEngine capacityEngine typeYear of construction BMW 3er (E90/E92/E93)M3309kW / 420hp3999cm³S65 B40 A06.07 - 06.13