Competition intercooler kit | fits Audi A1 (GB) 40TFSI, VW Polo (AW1) 2.0 TSI GTI | Wagner Tuning

The roof edge spoiler is suitable for the G87 and G42 and enhances the rear of the latest generation of the 2 Series by adding a subtle touch of aggression without losing the clean look of the vehicle.Details:- 100% pure pre-preg carbon fibre construction- High gloss finish- V-design- Fit guarantee- Registration according to §21 possible Compatible vehicles:- BMW G87 2 Series M2 (2023+)- BMW G42 2 Series M240i Coupe (2022+)- BMW G42 2 Series Coupe (2022+)Note: This is NOT an original BMW product!

KW V1 coilover suspension Sportiness paired with outstanding looks. With factory pre-configured damping.Our entry-level model for more driving pleasure through an appealing and individually adjustable lowering is the KW V1 coilover suspension in the KW typical "inox-line". Thanks to its high-quality workmanship, the consistent use of stainless steel struts, corrosion-resistant springs and harmonised components, it stands for many years of driving pleasure - and not just for the life of the car. Stepless loweringThe KW V1 enables maximum lowering within the tested adjustment range. This varies depending on the vehicle model and can, for example, be between 30 and 70 millimetres or 50 to 90 millimetres for an individual lowering. Thanks to the dirt-resistant trapezoidal thread and the polyamide threaded ring, the stepless lowering can be varied quickly and easily even years later. Depending on the vehicle, the lowering is carried out either on the wheel-guiding KW stainless steel suspension struts or on the rear axle height adjustment for non-wheel-guiding double-wishbone rear axles. The benchmark for sporty, dynamic tuning fansWith its harmonious basic set-up for sporty driving on the road, the KW V1 convinces the discerning tuning fan. Our development engineers determine a specific damper set-up and spring rate for each vehicle in order to increase your driving pleasure with the optimum balance of sportiness and suitability for everyday use. After all, you are not buying just any coilover suspension, but a KW coilover suspension that has been specially developed and tuned for your vehicle type. As a manufacturer, KW only uses its own resources, high-quality components and the same damper technology as mass-produced manufacturers. With the KW V1, the rolling and rolling movements of the vehicle body are reduced during compression, allowing you to benefit from unadulterated directness and sportier handling when driving. Our experience for your driving pleasureAs a manufacturer of customised suspension solutions for road and racing, we have been the market leader and innovation driver for over 25 years. No matter where in the world, sporty drivers, car manufacturers and tuners rely on our KW coilovers "Made in Germany". Every KW coilover suspension is subjected to extensive load tests during production and is developed and manufactured directly at our company headquarters in Fichtenberg, Swabia, in order to fulfil the high standards of our KW quality management. As a German manufacturer, it is a matter of course for us to provide a multi-year warranty on our KW coilover suspension kits, which exceed OEM quality and cover over 4,600 applications. When installed by one of our KW specialist dealers, this warranty is valid for up to five years. - Optimally adjusted in advance- sporty and harmonious damping technology- Stainless steel technology "inox-line"- Individually height-adjustable- Tested adjustment range- Ready-to-install complete solution- High-quality components for a long service life- Complete documentation for easy handling Setup - factory pre-configured damping setupThe KW V1 has a vehicle-specific, permanently configured damper setup. The spring and the damper are perfectly matched to each other so that you experience an optimum balance of sportiness and suitability for everyday use when driving. Even with a full payload and maximum axle loads, the dampers always work with a sporty characteristic curve. The KW V1 is particularly interesting for tuning enthusiasts who prioritise the show & shine concept. Please note the conditions and instructions for this product: - VA + HA height-adjustable (VA threaded struts) Technical info: Lowering VA/HA (mm): 10-30/15-35 Design: V1 Hardness adjustment: none Material: stainless steel Adjustment VA/HA: thread/thread Approval: parts certificate (§19.3) Compatible vehicles: Manufacturer Model Version Body Fuel Performance Displacement Cylinder Drive AUDI A6 (4B) 4B2, C5 01/1997-08/2005 RS6 quattro notchback Petrol 331 KW 4172 ccm 8 All-wheel AUDI A6 Avant (4B) 4B5, C5 11/1997-01/2005 RS6 plus quattro estate petrol 353 KW 4172 ccm 8 all-wheel drive AUDI A6 Avant (4B) 4B5, C5 11/1997-01/2005 RS6 quattro estate petrol 331 KW 4172 ccm 8 all-wheel drive

KW V3 Clubsport coilover suspension incl. support bearing With an uncompromising technology transfer from racing to the road, the KW Clubsport coilovers convince.The KW Clubsport coilovers convince with their uncompromising combination of high-end racing technology with maintenance-free KW original equipment components and expertises.This gives you the ideal accessories to realise the full potential of your sports car at trackdays, sports driver training courses, tourist drives on Grand Prix circuits and on the Nürburgring Nordschleife. Developed for the toughest racetrack in the world: the Nürburgring NordschleifeEven in their basic set-up, KW Clubsport coilovers are tuned to the different track surfaces, steep bends, jumps and chicanes of the 20.8 kilometre long Nürburgring Nordschleife. After all, as one of the most successful suspension manufacturers and suppliers in motorsport, we are at home on the Nordschleife.In the VLN Endurance Championship alone, we equip over 70 racing teams and, as a suspension manufacturer, have supported six overall victories at the ADAC Zurich 24h Race Nürburgring in ten years. The winner of the ADAC GT Masters 2011 also relies on our racing expertise, from which the KW Clubsport coilovers benefit.The basic setup of the KW V3 Clubsport and KW V4 Clubsport with separate expansion tank, which is perfectly adapted to the Nordschleife, allows you to adjust your sports car even more individually to the desired sports tyre setup thanks to the numerous adjustment options.In addition to optionally available adjustable support bearings, you can adjust the damping forces of the KW Clubsport coilovers independently in the rebound and compression stages with the integrated KW V3 Clubsport coilover suspension technology like in racingWith the adjustment wheels for the rebound adjustment, you can fine-tune the recommended basic setup for your sports car and your individually installed performance components with 16 exact clicks. This allows you to directly influence changed wheel loads, for example to influence bodywork movements. Separate from the rebound adjustment, the KW V3 Clubsport allows you to adjust the compression damping with twelve exact clicks in the low-speed range to your requirements, such as the sports tyres used.These setting options allow you to consider individual setups to suit the vehicle weight, sports tyre characteristics, track characteristics and operating conditions. - Freely adjustable damping technology in rebound and compression damping- Stainless steel technology "inox-line"- Stepless lowering- Tested adjustment range- high-quality components for a long service life- Adjustable rebound damping with 16 exact clicks- Adjustable compression damping with 12 exact clicks- Unique, independently acting damping force adjustment- optionally available with aluminium Unibal support bearing. Setup: Application range and damper tuningThe KW V3 Clubsport coilover suspensions impress with their vehicle-specific setup for trackday events on the Nürburgring Nordschleife, as well as the possibility of quickly tuning these suspensions for other racetracks and individual performance sports cars. Please note the conditions and instructions for this product: - VA + HA height adjustable (VA coilover struts, HA springs with height adjustment + damper) - For vehicles with electronic damper control, this must be deactivated. Vehicle-specific KW decommissioning kits are not included in the scope of delivery. - Dampers have easy-to-use adjustment wheels. Due to the design, the rebound stage can only be adjusted when the piston rod is accessible. - Clubsport suspension with support bearing: only available with VA support bearing Technical information: Lowering VA/HA (mm): 20-45/25-50 Version: V3 Clubsport Hardness adjustment: Rebound and compression Material: Stainless steel Adjustment VA/HA: Thread/thread Approval: Parts certificate (§19.3) Compatible vehicles: Manufacturer Model Version Body Fuel Performance Displacement Cylinder Drive AUDI A1 (8X) 8X1, 8XK 05/2010-10/2018 S1 quattro hatchback petrol 170 KW 1984 ccm 4 all-wheel drive AUDI A1 Sportback (8X) 8XA, 8XF 09/2011-10/2018 S1 quattro hatchback petrol 170 KW 1984 ccm 4 all-wheel drive

KW V3 Clubsport coilover suspension incl. support bearing With an uncompromising technology transfer from racing to the road, the KW Clubsport coilovers convince.The KW Clubsport coilovers convince with their uncompromising combination of high-end racing technology with maintenance-free KW original equipment components and expertises.This gives you the ideal accessories to realise the full potential of your sports car at trackdays, sports driver training courses, tourist drives on Grand Prix circuits and on the Nürburgring Nordschleife. Developed for the toughest racetrack in the world: the Nürburgring NordschleifeEven in their basic set-up, KW Clubsport coilovers are tuned to the different track surfaces, steep bends, jumps and chicanes of the 20.8 kilometre long Nürburgring Nordschleife. After all, as one of the most successful suspension manufacturers and suppliers in motorsport, we are at home on the Nordschleife.In the VLN Endurance Championship alone, we equip over 70 racing teams and, as a suspension manufacturer, have supported six overall victories at the ADAC Zurich 24h Race Nürburgring in ten years. The winner of the ADAC GT Masters 2011 also relies on our racing expertise, from which the KW Clubsport coilovers benefit.The basic setup of the KW V3 Clubsport and KW V4 Clubsport with separate expansion tank, which is perfectly adapted to the Nordschleife, allows you to adjust your sports car even more individually to the desired sports tyre setup thanks to the numerous adjustment options.In addition to optionally available adjustable support bearings, you can adjust the damping forces of the KW Clubsport coilovers independently in the rebound and compression stages with the integrated KW V3 Clubsport coilover suspension technology like in racingWith the adjustment wheels for the rebound adjustment, you can fine-tune the recommended basic setup for your sports car and your individually installed performance components with 16 exact clicks. This allows you to directly influence changed wheel loads, for example to influence bodywork movements. Separate from the rebound adjustment, the KW V3 Clubsport allows you to adjust the compression damping with twelve exact clicks in the low-speed range to your requirements, such as the sports tyres used.These setting options allow you to consider individual setups to suit the vehicle weight, sports tyre characteristics, track characteristics and operating conditions. - Freely adjustable damping technology in rebound and compression damping- Stainless steel technology "inox-line"- Stepless lowering- Tested adjustment range- high-quality components for a long service life- Adjustable rebound damping with 16 exact clicks- Adjustable compression damping with 12 exact clicks- Unique, independently acting damping force adjustment- optionally available with aluminium Unibal support bearing. Setup: Application range and damper tuningThe KW V3 Clubsport coilover suspensions impress with their vehicle-specific setup for trackday events on the Nürburgring Nordschleife, as well as the possibility of quickly tuning these suspensions for other racetracks and individual performance sports cars. Please note the conditions and instructions for this product: - VA + HA height adjustable (VA coilover struts, HA springs with height adjustment + damper) - For vehicles with electronic damper control, this must be deactivated. Vehicle-specific KW decommissioning kits can be found in the accessories table. - The dampers have easy-to-operate adjustment wheels. Due to the design, the rebound stage can only be adjusted if the piston rod is accessible. - Clubsport suspension with support bearing: only available with VA support bearing Technical information: Lowering VA/HA (mm): 30-50/30-50 Version: V3 Clubsport Hardness adjustment: Rebound and compression Material: Stainless steel Adjustment VA/HA: Thread/thread Approval: Parts certificate (§19.3) Compatible vehicles: Manufacturer Model Version Body Fuel Performance Displacement Cylinder Drive VW POLO VI (AW, AW1, BZ1) 06/2017- 2.0 GTI Hatchback Petrol 147 KW 1984 ccm 4 Front-wheel drive VW POLO VI (AW, AW1, BZ1) 06/2017- GTI Hatchback Petrol 152 KW 1984 ccm 4 Front-wheel drive

KW V3 coilover suspension Unlimited individuality for performance & comfort. Separate damper force adjustment for rebound and compression damping.As with every KW coilover suspension, our suspension engineers also develop a sporty and harmonious basic set-up for the vehicle-specific applications of the KW V3. In addition to tests on our KW 7-post driving dynamics test bench, we also carry out extensive test drives on country roads, the motorway and even on the Nürburgring Nordschleife, kilometre by kilometre, to guarantee you the perfect suspension set-up. For years, the KW V3, one of the world's top aftermarket products, has been the reference for coilover suspensions. With its damper characteristics, high-quality workmanship and excellent durability, it has impressed discerning sports car drivers, tuners, large and small series manufacturers such as Alpina, MTM, Manthey, Oettinger and many other well-known companies in the international automotive industry. Cutting-edge technology from motorsportYou get much more than a sporty lowering and excellent handling on all roads with the KW V3. It is based on our many years of experience as a suspension manufacturer and supplier in international motorsport, such as in the ADAC GT Masters touring car series, FIA GT1, FIA GT3, International GT Open, WTC, VLN and also in the legendary ADAC Zurich 24h Race Nürburgring.Similar to our racing coilovers from the KW Competition programme, the rebound and compression damping of the KW V3 can be adjusted independently of each other. This individual tuning option is appreciated by tuners, sports car manufacturers, tuners and demanding drivers worldwide. The perfect suspension setup for significantly more driving dynamicsIf you have already carried out initial performance modifications to your sporty road vehicle, it is easy to incorporate these into the damper set-up in a targeted manner with the KW V3. The patented KW valve technology for the separate adjustment of the rebound and compression damping allows you to customise the vehicle-specific basic set-up from KW. For example, the KW bottom valve, which can be adjusted in twelve clicks in the low-speed range of the compression stage, gives you the freedom to even take the tyre characteristics of your high and ultra-high performance road tyres into account in the suspension set-up.Thanks to the patented compression adjustment at the lower piston end of the stainless steel housing, you don't even need any tools. The adjustable compression adjustment with its twelve precise clicks allows you to influence body roll and body roll movements by hand without having to change the rebound damping to match the spring rate.With the individually adjustable rebound damping of the KW V3, you can directly influence the handling and comfort through the exact click adjustment. Depending on the vehicle type, the rebound valves of the KW twin-tube dampers are adjusted at the upper end of the piston rod via an integrated adjustment wheel or the slip-on adjustment wheel included in the scope of delivery.By increasing the rebound force via the adjustment wheel, the body movements on the body are reduced. As a result, your car tracks more accurately and you have even more stability at higher cornering speeds. If, for example, you change from the approved wheel/tyre combinations of your car manufacturer to larger rims, you can use the KW V3 to perfectly match the handling of your car and your new alloy wheels. High-quality, customised and durableThe KW V3 is subjected to extensive quality tests during production and every single damper is checked. This is the only way we can fulfil our claim to provide a warranty of up to five years when a KW coilover suspension V3 is installed by a KW specialist dealer. Due to the filigree workmanship and the use of high-quality components, the KW coilover struts made of stainless steel, for example, are 100 per cent rust-free and have an unlimited service life.This means that the functionality of the stepless lowering system via the dirt-resistant KW trapezoidal thread and the KW polyamide threaded ring is not impaired even after many years. Thanks to the individual lowering with its stepless adjustment range, you can also emphasise the sportiness of your vehicle visually. A feature that is very popular in the performance-orientated tuning scene. - Freely adjustable damping technology in rebound and compression damping- inox-line stainless steel technology- Individual, stepless lowering- Tested adjustment range- high-quality components for a long service life- adjustable rebound damping with 16 exact clicks- 12-way adjustable compression damping with click adjustment- Unique, independently acting damping force adjustment Setup: The individually adjustable rebound & compression damping of the KW V3The KW V3 is the ideal accessory for performance-orientated drivers and tuning enthusiasts who demand a high level of sportiness from their vehicles. The dampers, which are separately adjustable in rebound and compression, allow extensive damper tuning with their sophisticated click adjustment. This makes it easy to directly influence the turn-in behaviour, directional stability, tyre grip and handling characteristics for safe controllability at the limit. Please note the conditions and instructions for this product: - VA + HA height-adjustable (VA coilover struts, HA springs with height adjustment + dampers) - Dampers have easy-to-use adjustment wheels. Due to the design, the rebound stage can only be adjusted when the piston rod is accessible. Technical information: Lowering VA/HA (mm): 15-40/25-50 Design: V3 Hardness adjustment: Rebound and compression Material: Stainless steel Adjustment VA/HA: Thread/thread Approval: Parts certificate (§19.3) Compatible vehicles: Manufacturer Model Version Body Fuel Performance Displacement Cylinder Drive FORD FIESTA VII (JHH) 05/2017- 1.5 ST EcoBoost Hatchback Petrol 147 KW 1496 ccm 3 Front-wheel drive