Tailgate Duck-Style Carbon | fits BMW M2/2 Series (G87/G42) S58 | Aulitzky Tuning

KW V1 coilover suspension Sportiness paired with outstanding looks. With factory pre-configured damping.Our entry-level model for more driving pleasure through an appealing and individually adjustable lowering is the KW V1 coilover suspension in the KW typical "inox-line". Thanks to its high-quality workmanship, the consistent use of stainless steel struts, corrosion-resistant springs and harmonised components, it stands for many years of driving pleasure - and not just for the life of the car. Stepless loweringThe KW V1 enables maximum lowering within the tested adjustment range. This varies depending on the vehicle model and can, for example, be between 30 and 70 millimetres or 50 to 90 millimetres for an individual lowering. Thanks to the dirt-resistant trapezoidal thread and the polyamide threaded ring, the stepless lowering can be varied quickly and easily even years later. Depending on the vehicle, the lowering is carried out either on the wheel-guiding KW stainless steel suspension struts or on the rear axle height adjustment for non-wheel-guiding double-wishbone rear axles. The benchmark for sporty, dynamic tuning fansWith its harmonious basic set-up for sporty driving on the road, the KW V1 convinces the discerning tuning fan. Our development engineers determine a specific damper set-up and spring rate for each vehicle in order to increase your driving pleasure with the optimum balance of sportiness and suitability for everyday use. After all, you are not buying just any coilover suspension, but a KW coilover suspension that has been specially developed and tuned for your vehicle type. As a manufacturer, KW only uses its own resources, high-quality components and the same damper technology as mass-produced manufacturers. With the KW V1, the rolling and rolling movements of the vehicle body are reduced during compression, allowing you to benefit from unadulterated directness and sportier handling when driving. Our experience for your driving pleasureAs a manufacturer of customised suspension solutions for road and racing, we have been the market leader and innovation driver for over 25 years. No matter where in the world, sporty drivers, car manufacturers and tuners rely on our KW coilovers "Made in Germany". Every KW coilover suspension is subjected to extensive load tests during production and is developed and manufactured directly at our company headquarters in Fichtenberg, Swabia, in order to fulfil the high standards of our KW quality management. As a German manufacturer, it is a matter of course for us to provide a multi-year warranty on our KW coilover suspension kits, which exceed OEM quality and cover over 4,600 applications. When installed by one of our KW specialist dealers, the warranty is up to five years. - Optimally adjusted in advance- sporty and harmonious damping technology- Stainless steel technology "inox-line"- Individually height-adjustable- Tested adjustment range- Ready-to-install complete solution- High-quality components for a long service life- Complete documentation for easy handling Setup - factory pre-configured damping setupThe KW V1 has a vehicle-specific, permanently configured damper setup. The spring and damper are perfectly matched to each other so that you experience an optimum balance of sportiness and suitability for everyday use when driving. Even with a full payload and maximum axle loads, the dampers always work with a sporty characteristic curve. It is interesting to note that the KW V1 is particularly popular with tuning enthusiasts who prioritise the idea of show & shine. Please note the conditions and instructions for this product:- VA + HA height-adjustable (VA coilover struts, HA springs with height adjustment + damper) Technical information:Lowering VA/HA (mm):5-30/5-20Version: V1Hardness adjustment: noneMaterial: Stainless steelAdjustment VA/HA: thread/threadApproval: Parts certificate (§19.3) Compatible vehicles:Manufacturer Model Version Body Fuel Performance Displacement Cylinder DriveMERCEDES-BENZ C-KLASSE Coupe (C204) 204, 204 AMG, 204K 01/2011- C 63 AMG (204.377) Coupe Petrol 336 KW 6208 ccm 8 Rear-wheel driveMERCEDES-BENZ C-CLASS Coupe (C204) 204, 204 AMG, 204K 01/2011- C 63 AMG (204.377) Coupe Petrol 358 KW 6208 ccm 8 Rear-wheel driveMERCEDES-BENZ C-CLASS Coupe (C204) 204, 204 AMG, 204K 01/2011- C 63 AMG (204.377) Coupe Petrol 373 KW 6208 ccm 8 Rear-wheel driveMERCEDES-BENZ C-KLASSE Coupe (C204) 204, 204 AMG, 204K 01/2011- C 63 AMG (204.377) Coupe Petrol 380 KW 6208 ccm 8 Rear-wheel drive

Suitable for the following vehicles: Mercedes Benz W176 A 45 AMG 265-280KW/360-381hp (2013-2018) Mercedes Benz C117 CLA 45 AMG 265-280KW/360-381hp (2013-2018) Mercedes Benz X156 GLA 45 AMG 265-280KW/360-381hp (2014-2019) The 2.0L M 133 turbo engine of the specified A-Class models from AMG is equipped with an indirect charge air cooling circuit. This means that the charge air cooling process is not realised using the ambient air as a cooling medium (as usual), but with the help of a separate cooling water circuit. A reduction in the cooling water temperature can therefore be directly equated with an improved cooling performance of the charge air. This is precisely where the advantages of the WAGNERTUNING upgrade water coolers come into play. The newly developed competition racing nets of the WAGNERTUNING high-performance water coolers increase the radiator volume of the standard water coolers by a total of 78%. The ratio between the inner and outer cooling surface generates maximum heat transfer and at the same time allows the neighbouring components (e.g. the engine water cooler behind it) sufficient airflow for heat exchange. Furthermore, the water coolers are equipped with a thermally conductive anti-corrosion coating to ensure a long-lasting cooling effect. Installation of the system is also straightforward and plug & play with the help of our installation instructions. Now with parts certificate! OEM front radiator dimensions: 640 mm x 390 mm x 16 mm V = 3.99 litres A = 2496 cm² WT front radiator dimensions: 616 mm x 362 mm x 32 mm V = 7.14 litres A = 2230 cm² OEM side cooler dimensions: 248 mm x 180 mm x 40 mm V = 1.79 litres A = 446 cm² WT side cooler dimensions: 252 mm x 184 mm x 68 mm V = 3.15 litres A = 464 cm² Attention: Not approved in the area of the StVZO.

Facts:Performance increase: 15-20hpExpert opinion: withoutManufacturer: EventuriMaterial: CarbonExpert opinion: without The Mercedes A35 AMG Eventuri intake system was developed to provide the turbo with a less restrictive flow path while keeping intake temperatures low. Reducing heat suction and increasing internal volume are the main considerations when developing an intake system for turbocharged engines. In the A35, the intake system is located in close proximity to the exhaust manifold, which quickly heats up the engine compartment. High temperatures have a detrimental effect on engine performance, as the turbo has to build up boost pressure with heated, less dense air. Therefore, the only way to reduce IAT to a minimum is to have a completely sealed intake tract. To reduce the restrictions of a closed intake tract, we increased the volume of the airbox by relocating the ECU and providing an opening in the airbox on the cold side, away from the direct heat of the manifold. The carbon inlet pipe has a larger internal volume with an initial internal diameter of 111mm (4.4?) which tapers smoothly to match the turbo inlet pipe diameter. Finally, we use a custom high-flow dry filter that is ISO approved and has a larger filter area than the stock filter. Dyno testsThe dyno tests were carried out by MSL Performance, a Mercedes specialist based in the UK. A fully standard A35 AMG was tested with the standard airbox and then with the Eventuri intake system, with the same external conditions. As can be seen below, the intake system offers an increase in power throughout the rev range. The highlighted point shows a significant power gain as the intake allows a higher flow rate in the higher rev range where the stock airbox becomes a restriction. The resulting performance gains are noticeable on the road, with better throttle response and improved acceleration times. With a tuned A35 we would expect even better gains as the demand from the turbo increases. The Eventuri A35 intake system consists of a number of components designed for a specific purpose and manufactured to the highest standards. We use 100% pre-impregnated carbon fiber without fiberglass, which means we can achieve a smooth inner surface to get a smoother airflow. Here are the details for each component and the design ethos behind them: Each intake system consists of:Carbon airboxCustom high-flow dry-cone filterCarbon intake tubeCNC-machined intake flangeLaser-cut stainless steel brackets and ECU coverSilicone coupler with OEM clamps Compatible vehicles:VehicleVehicle typePowerEngine capacityEngine typeYear of construction Mercedes A-Klasse (W177/V177)A250 / 4-matic165kW / 224hp1991cm³M 260.92003.18 - Mercedes A-Klasse (W177/V177)A35 AMG 4-matic225kW / 306hp1991cm³M 260.92009.18 - Mercedes CLA (C118/X118)A250 / 4-matic165kW / 224hp1991cm³M 260.92003.19 - Mercedes CLA (C118/X118)CLA35 AMG 4-matic225kW / 306hp1991cm³M 260.92004.19 - Mercedes GLB (X247)GLB250 / 4-matic165kW / 224hp1991cm³M 260.92008.19 - Mercedes GLB (X247)GLB35 AMG 4-matic225kW / 306hp1991cm³M 260.92008.19 -

KW coilover suspension DDC ECU KW Dynamic Damping Control ECU Individuality at the push of a button. The KW DDC coilovers are the intelligent suspension solution for retrofitting from the KW iSuspension product range. They combine the advantages of an adaptive damping system with a vehicle-specific sporty and harmonious damper characteristic with a stylish and sporty lowering. The adaptive KW coilovers are available in the KW DDC ECU version with optional app control for vehicles without actively controlled standard suspension and as KW DDC Plug & Play version for selected vehicle models with adaptive standard suspension. The adaptive KW DDC ECU coilovers allow a stepless lowering in the tested adjustment range. Thanks to the dirt-resistant trapezoidal thread and the polyamide threaded ring, the stepless lowering can be varied quickly and easily even after years. Depending on the vehicle, lowering takes place either on the wheel-guiding KW stainless steel suspension struts or, in the case of non-wheel-guiding double wishbone rear axles, on the rear axle height adjustment. No matter where in the world, sporty drivers, car manufacturers and tuners trust in our KW technology “Made in Germany”. Every KW coilover suspension is subjected to extensive load tests during production and is developed and manufactured directly at our company headquarters in Fichtenberg, Swabia, in order to meet the high standards of our KW quality management. As a German manufacturer, it is a matter of course for us to offer a multi-year warranty on our KW coilover suspension kits, which exceed OEM quality and cover over 4,600 applications. It is up to five years when installed by one of our KW specialist dealers. The adaptive KW DDC ECU coilovers with app control are currently available for Audi, BMW, Mercedes-Benz, Porsche, VW and many other vehicles such as the Range Rover Evoque. - retrofittable electronic damper adjustment, combined with the advantages of a KW coilover suspension - with optional app control - Three damping setups: Comfort / Sport / Sport + - Operation via retrofit button or optional app - Create your own setups intuitively via KW DDC app KW DDC button - 1x button, 3x learn more The scope of delivery of the KW DDC ECU coilover kit also includes a KW DDC button. This allows you to select the KW DDC driving modes “Comfort”, “Sport” and “Sport+” directly from the cockpit. The KW DDC button changes the color to fit the KW DDC APP. W-LAN module & app control Optionally available app control for live suspension tuning via iPhone, iPod touch, iPad. Experience top-class innovation and quality “Made in Germany”: the KW DDC (Dynamic Damping Control) coilover suspension with ECU (Electronic Control Unit). The coilover suspension with its electronically adjustable dampers enables intelligent suspension tuning via app control and is already available for numerous vehicles without adaptive standard suspension. This allows you to upgrade your vehicle with adaptive damper control and optionally adapt it to your driving style via the KW DDC app. You do not need any tools or have to work on the dampers yourself. The free KW DDC App in combination with our optionally available W-Lan module is your tool to perform an individual damper tuning live and in real time. Please note the conditions and instructions for this product: - VA + HA height-adjustable (VA coilover struts, HA springs with height adjustment + damper) Technical info: Lowering VA/HA (mm): 10-35/5-25 Version: DDC - ECU Hardness adjustment: Rebound and compression stage Material: Stainless steel Adjustment VA/HA: thread/thread Approval: Parts certificate (§19.3) Compatible vehicles: Manufacturer Model Version Body Fuel Performance Displacement Cylinder Drive BMW 1 Series Coupe (E82) 182, 1C, M-V 10/2006-10/2013 M Coupe Petrol 250 KW 2979 ccm 6 Rear-wheel drive