Air collector Carbon | fits BMW M3 (E90/E92/E93) 420hp S65 | Eventuri

Facts: Material: Carbon Manufacturer: Eventuri Parts certificate: A certificate is available for this product for certain regions and vehicles (details below) Parts certificate The manufacturer's specifications apply for installation. The availability of a certificate is no guarantee that the product can be installed in the corresponding vehicle. A certificate is available for this product for the following regions and vehicles: * DE/AT: Vehicle registration document, field K --- CH/LI: Vehicle licence, field 24 Country model type approval* DE/AT BMW E90 M3 e1*2007/46*0377*.. DE/AT BMW E92 M3 e1*2007/46*0377*.. DE/AT BMW E93 M3 e1*2007/46*0377*.. DE/AT BMW GTS e1*KS07/46*0012*.. DE/AT BMW M3 e1*2001/116*0345*.. CH/LI BMW M3 1BB471 CH/LI BMW M3 1BB570 CH/LI BMW M3 1BB607 CH/LI BMW M3 1BB669 CH/LI BMW M3 1BB955-1BB957 CH/LI BMW M3 1BC611-1BC612 Compatible vehicles: VehicleVehicle typePowerEngine capacityEngine typeYear of constructionBMW 3 Series (E90/E92/E93)M3309kW / 420hp3999cm³S65 B40 A06.07 - 06.13

Facts: Material: Carbon Manufacturer: Eventuri Parts certificate: without A legendary add-on for a legendary car! Our E9X carbon ducts are a direct replacement for the OEM plastic ducts to add the finishing touches to the engine bay. These ducts are made from prepreg carbon and match the rest of our E9X range for the ultimate OEM+ theme. We have also replaced the flexible connector between the ducts and the airbox with an EPDM coupling with our raised V logo. During development we considered adding air scoops to the front duct, but after analysis we realised that there was no performance benefit due to the small opening between the ducts and the airbox, so we decided not to add air scoops. This also leaves the grill openings clear for optimum flow to the radiator. The Eventuri carbon ducts are available in both gloss and matte finishes to match our plenum, intake and airbox lid. Each set consists of: Carbon fibre front duct Carbon fibre rear duct Customised EPDM coupler Compatible vehicles: VehicleVehicle typePowerEngine capacityEngine typeYear of constructionBMW 3 Series (E90/E92/E93)M3309kW / 420hp3999cm³S65 B40 A06.07 - 06.13

Facts:Performance increase: +8-10 hp, +10-12 NmMaterial: CarbonManufacturer: EventuriParts certificate: A certificate is available for this product for certain regions and vehicles (details below) A legendary add-on for a legendary car! Extensive studies of the original, very well developed Intake have paid off in the design of the intake system from Eventuri, because in the end an improvement could still be achieved. The new intake system for the E90, E92 and E93 guarantees a noticeable increase in performance thanks to a frictionless air flow in the new, one-piece intake manifold.In contrast to many other Eventuri intake systems, only the filter, the intake pipe and the intake scoop need to be replaced. In addition to easier installation, this is reflected above all in the price. The new scoop directs the airflow in such a way that the high pressure can be used without frictional losses due to the position of the air intake directly under the headlights. The resulting significantly cooler and faster airflow leads to a clear optimization of the overall airflow.In repeated tests, these small optimizations allow an increase in performance of between 8 and 10 hp and 10 - 12 Nm more! The intake system is supplied with:Efficient high flow cone with urethane filterCarbon scoopInlet pipe made of full carbonLaser-cut debris shieldLaser-cut suspension Parts certificateThe manufacturer's specifications apply for installation. An existing certificate is no guarantee that the product can also be installed in the corresponding vehicle. A certificate is available for this product for the following regions and vehicles:* DE/AT: Vehicle registration document, field K --- CH/LI: Vehicle registration document, field 24Country model type approval*DE/AT BMW E90 M3 e1*2007/46*0377*..DE/AT BMW E92 M3 e1*2007/46*0377*..DE/AT BMW E93 M3 e1*2007/46*0377*..DE/AT BMW GTS e1*KS07/46*0012*..DE/AT BMW M3 e1*2001/116*0345*..CH/LI BMW M3 1BB471CH/LI BMW M3 1BB570CH/LI BMW M3 1BB607CH/LI BMW M3 1BB669CH/LI BMW M3 1BB955-1BB957CH/LI BMW M3 1BC611-1BC612 Compatible vehicles:VehicleVehicle typePowerEngine capacityEngine typeYear of construction BMW 3er E90/E92/E93)M3309kW / 420hp3999cm³S65 B40 A06.07 - 06.13

MOVIT DDE steel brake system 370x35mm (6 piston calliper) for the front axle, from 18 inch rims upwardsApplication-focussed development is the cornerstone of this high-performance brake system. The required balance of weight, performance and durability is optimally combined. The uncompromising selection of materials in production results in a highly unique product that meets the diverse requirements of extreme automotive applications. The most important features of the MOVIT brake system are- The progressive staggering of the piston diameters, matched to the vehicle, so that precisely parallel contact pressure between the pad and the disc is guaranteed. This enables even wear of the brake pads and ensures even heat transfer and a reduced system temperature.- Very good heat dissipation due to the open design of the brake pad contour.- Calipers manufactured from high-strength, highly tempered aircraft aluminium 7075 with high-quality material properties (stiffer components, more homogeneous structure), hard anodised and coated with a triple paint finish.- Optimised stability due to the length of the callipers- Larger brake disc diameter and thickness, more cross holes (each pre-cast hole is re-drilled and countersunk, which has a favourable effect on the flow).- The brake discs are thermally tempered.- The optimised DDE ventilation system (double directional evolvent system) of the brake disc has an 80% larger surface area compared to other brake discs, the temperature of the brake disc is significantly reduced and therefore also the wear.- Long service life of the wearing parts, excellent response behaviour, steel flex lines ensure consistent performance.- Optimally matched brake pads ensure fading resistance, a long service life and reduced wear on spare parts Attention: The conversion means that only rims with at least 18 inches can be fitted! The chassis number of the vehicle on which the brakes are fitted is required for the parts certificate. MOVIT sports brake callipers, 6s5, 6-piston- Milled from high-strength aircraft aluminium 7075- Two-piece- Use of maximum disc size due to long design- Significantly improved rigidity and extended contact surface of the pad- Uniform heat transfer- Reduced system temperature- Low, even pad wear- Progressive piston staggering- Crown system for fixing the brake hose- RAPAD-X system for quick brake pad replacement without removing the caliper from the bracket- Open brake pad track for optimised cooling- Maximum stability- Maximum braking force MOVIT sports brake discs, 370x35mm, 2-piece- Highly efficient DDE cooling system- Perforated for optimum response behaviour even on wet roads- Maximum fading resistance- Special alloy for high thermal conductivity MOVIT comfort brake pads, BE-6s1- Enlarged friction surface- Lower system temperature- Uniform heat transfer- Longer service life Scope of delivery:2x MOVIT brake caliper (left/right)2x MOVIT brake disc (left/right)2x vehicle-specific brake caliper adapter1x set of comfort brake pads2x steel flex lines1x assembly material1x installation instructions and running-in instructions1x parts certificate Compatible vehicles:BMW 1 Series F20 / F21 (also M)Ford Focus RS CB4 / MKIIAudi RS3 8PAudi RS4 B5Audi S4 Type 8D / B5BMW M3 E46BMW M3 E46 CSLBMW M3 E92Ford Mustang V Shelby GT 500Mercedes Benz W639 Vito / VianoVolvo XC90 1st gen. from 2011 onwardsVW Golf VII GTI / GTD 57 series pistonsVW Golf VII GTI / GTD 57 series pistonsVW GOLF VII GTI Clubsport / Performance 60 series pistonsVW Golf VII RVW Golf VII RVW T5 / T6 Multivan

Facts: - 3" (76mm) stainless steel rear silencer - with Thermo-Integral insulation - Tailpipe not selectable, pipe outlets for original trim in the rear apron - Original exhaust flap control is decommissioned - without approval* Scope of delivery: - 1x rear silencer Compatible vehicles:VehicleVehicle typePowerEngine capacityEngineYear of constructionFerrari F8 Tributo Coupe3.9530kW / 721hp3902cm³F 154 CD03.19 -Ferrari F8 Spider3.9530kW / 721hp3902cm³F 154 CD12.19 - *ATTENTION :Exhaust systems without approval are not permitted for use on public roads and are only intended for racing purposes! If you nevertheless install a product without approval in your vehicle and use it within the scope of the StVZO, you are liable to prosecution. Possible consequences that you can expect in this case: Expiry of the operating licence in accordance with §19 of the StVZO and possible resulting immobilisation of the vehicle. Other possible consequences, such as a charge of tax evasion, as well as possible investigations by the environmental authorities are at the discretion of the investigators.

Facts:Performance increase: 15-20hpExpert opinion: withoutManufacturer: EventuriMaterial: CarbonExpert opinion: without The Mercedes A35 AMG Eventuri intake system was developed to provide the turbo with a less restrictive flow path while keeping intake temperatures low. Reducing heat suction and increasing internal volume are the main considerations when developing an intake system for turbocharged engines. In the A35, the intake system is located in close proximity to the exhaust manifold, which quickly heats up the engine compartment. High temperatures have a detrimental effect on engine performance, as the turbo has to build up boost pressure with heated, less dense air. Therefore, the only way to reduce IAT to a minimum is to have a completely sealed intake tract. To reduce the restrictions of a closed intake tract, we increased the volume of the airbox by relocating the ECU and providing an opening in the airbox on the cold side, away from the direct heat of the manifold. The carbon inlet pipe has a larger internal volume with an initial internal diameter of 111mm (4.4?) which tapers smoothly to match the turbo inlet pipe diameter. Finally, we use a custom high-flow dry filter that is ISO approved and has a larger filter area than the stock filter. Dyno testsThe dyno tests were carried out by MSL Performance, a Mercedes specialist based in the UK. A fully standard A35 AMG was tested with the standard airbox and then with the Eventuri intake system, with the same external conditions. As can be seen below, the intake system offers an increase in power throughout the rev range. The highlighted point shows a significant power gain as the intake allows a higher flow rate in the higher rev range where the stock airbox becomes a restriction. The resulting performance gains are noticeable on the road, with better throttle response and improved acceleration times. With a tuned A35 we would expect even better gains as the demand from the turbo increases. The Eventuri A35 intake system consists of a number of components designed for a specific purpose and manufactured to the highest standards. We use 100% pre-impregnated carbon fiber without fiberglass, which means we can achieve a smooth inner surface to get a smoother airflow. Here are the details for each component and the design ethos behind them: Each intake system consists of:Carbon airboxCustom high-flow dry-cone filterCarbon intake tubeCNC-machined intake flangeLaser-cut stainless steel brackets and ECU coverSilicone coupler with OEM clamps Compatible vehicles:VehicleVehicle typePowerEngine capacityEngine typeYear of construction Mercedes A-Klasse (W177/V177)A250 / 4-matic165kW / 224hp1991cm³M 260.92003.18 - Mercedes A-Klasse (W177/V177)A35 AMG 4-matic225kW / 306hp1991cm³M 260.92009.18 - Mercedes CLA (C118/X118)A250 / 4-matic165kW / 224hp1991cm³M 260.92003.19 - Mercedes CLA (C118/X118)CLA35 AMG 4-matic225kW / 306hp1991cm³M 260.92004.19 - Mercedes GLB (X247)GLB250 / 4-matic165kW / 224hp1991cm³M 260.92008.19 - Mercedes GLB (X247)GLB35 AMG 4-matic225kW / 306hp1991cm³M 260.92008.19 -