Air filter cover Carbon | fits BMW M3 (E90/E92/E93) 420hp S65 | Eventuri

Facts: Material: Carbon Manufacturer: Eventuri Parts certificate: A certificate is available for this product for certain regions and vehicles (details below) Parts certificate The manufacturer's specifications apply for installation. The availability of a certificate is no guarantee that the product can be installed in the corresponding vehicle. A certificate is available for this product for the following regions and vehicles: * DE/AT: Vehicle registration document, field K --- CH/LI: Vehicle licence, field 24 Country model type approval* DE/AT BMW E90 M3 e1*2007/46*0377*.. DE/AT BMW E92 M3 e1*2007/46*0377*.. DE/AT BMW E93 M3 e1*2007/46*0377*.. DE/AT BMW GTS e1*KS07/46*0012*.. DE/AT BMW M3 e1*2001/116*0345*.. CH/LI BMW M3 1BB471 CH/LI BMW M3 1BB570 CH/LI BMW M3 1BB607 CH/LI BMW M3 1BB669 CH/LI BMW M3 1BB955-1BB957 CH/LI BMW M3 1BC611-1BC612 Compatible vehicles: VehicleVehicle typePowerEngine capacityEngine typeYear of constructionBMW 3 Series (E90/E92/E93)M3309kW / 420hp3999cm³S65 B40 A06.07 - 06.13

Facts: Material: Carbon Manufacturer: Eventuri Parts certificate: without A legendary add-on for a legendary car! Our E9X carbon ducts are a direct replacement for the OEM plastic ducts to add the finishing touches to the engine bay. These ducts are made from prepreg carbon and match the rest of our E9X range for the ultimate OEM+ theme. We have also replaced the flexible connector between the ducts and the airbox with an EPDM coupling with our raised V logo. During development we considered adding air scoops to the front duct, but after analysis we realised that there was no performance benefit due to the small opening between the ducts and the airbox, so we decided not to add air scoops. This also leaves the grill openings clear for optimum flow to the radiator. The Eventuri carbon ducts are available in both gloss and matte finishes to match our plenum, intake and airbox lid. Each set consists of: Carbon fibre front duct Carbon fibre rear duct Customised EPDM coupler Compatible vehicles: VehicleVehicle typePowerEngine capacityEngine typeYear of constructionBMW 3 Series (E90/E92/E93)M3309kW / 420hp3999cm³S65 B40 A06.07 - 06.13

Facts:Performance increase: +8-10 hp, +10-12 NmMaterial: CarbonManufacturer: EventuriParts certificate: A certificate is available for this product for certain regions and vehicles (details below) A legendary add-on for a legendary car! Extensive studies of the original, very well developed Intake have paid off in the design of the intake system from Eventuri, because in the end an improvement could still be achieved. The new intake system for the E90, E92 and E93 guarantees a noticeable increase in performance thanks to a frictionless air flow in the new, one-piece intake manifold.In contrast to many other Eventuri intake systems, only the filter, the intake pipe and the intake scoop need to be replaced. In addition to easier installation, this is reflected above all in the price. The new scoop directs the airflow in such a way that the high pressure can be used without frictional losses due to the position of the air intake directly under the headlights. The resulting significantly cooler and faster airflow leads to a clear optimization of the overall airflow.In repeated tests, these small optimizations allow an increase in performance of between 8 and 10 hp and 10 - 12 Nm more! The intake system is supplied with:Efficient high flow cone with urethane filterCarbon scoopInlet pipe made of full carbonLaser-cut debris shieldLaser-cut suspension Parts certificateThe manufacturer's specifications apply for installation. An existing certificate is no guarantee that the product can also be installed in the corresponding vehicle. A certificate is available for this product for the following regions and vehicles:* DE/AT: Vehicle registration document, field K --- CH/LI: Vehicle registration document, field 24Country model type approval*DE/AT BMW E90 M3 e1*2007/46*0377*..DE/AT BMW E92 M3 e1*2007/46*0377*..DE/AT BMW E93 M3 e1*2007/46*0377*..DE/AT BMW GTS e1*KS07/46*0012*..DE/AT BMW M3 e1*2001/116*0345*..CH/LI BMW M3 1BB471CH/LI BMW M3 1BB570CH/LI BMW M3 1BB607CH/LI BMW M3 1BB669CH/LI BMW M3 1BB955-1BB957CH/LI BMW M3 1BC611-1BC612 Compatible vehicles:VehicleVehicle typePowerEngine capacityEngine typeYear of construction BMW 3er E90/E92/E93)M3309kW / 420hp3999cm³S65 B40 A06.07 - 06.13

Our high-quality and large engine cover made of pre-preg carbon fibre is a great addition to enhance the style of your vehicle. The carbon fibre engine cover replaces the standard plastic part. When you buy Pre-Preg carbon fibre, you are investing in a higher quality and more durable material that will outlast other forms of carbon fibre and potentially save you money in the long run. Installation: Plug&Play Details:- 100% carbon fibre construction- High gloss finish- Performance style design- Supplied with 3M double-sided adhesive tape already attached- Use rubber adapter from the original engine cover + emblem- registration free Compatible vehicles with S58 engine:- BMW G87 M2 - BMW G80 M3 Sedan (2021+)- BMW G80 M3 Competition Sedan (2021+)- BMW G81 M3 Touring (2023+)- BMW G81 M3 Competition Touring (2023+)- BMW G82 M4 Coupé (2021+)- BMW G82 M4 Competition Coupé (2021+)- BMW G83 M4 Convertible (2021+)- BMW G83 M4 Competition Convertible (2021+) Note: This is NOT an original BMW product!

Facts: - Tailpipes 4x black - 3.0 inch stainless steel - MSD removal - electric flaps - Made in Germany (Lake Constance) -  with ECE approval* Scope of delivery: - 1x Aulitzky Exhaust rear silencer - 4x tailpipes black - ECE handout Compatible vehicles: VehicleVehicle typePower outputengine capacityEngineYear of constructionBMW 2er (G42)M240i xDrive275kW / 374PS2998cm³B58 B30 B08.21 - *This exhaust system has ECE approval so that it can be used within the scope of the StVZO without registration in the vehicle documents.

Facts: Performance increase (standard Golf R): 10-13hp, 12-15Nm Performance increase (tuned Golf R): 15-20hp, 25-30Nm Material: Carbon fibre Manufacturer: Eventuri Parts certificate: A certificate is available for this product for certain regions and vehicles (details below) The MK8 Golf GTi/R intake manifold is a complete revision of the standard intake manifold up to the turbo inlet. Taking inspiration from our RS3 intake, we have maximised the space available to create an intake that is suitable for all power levels, from standard specification through to high performance systems with hybrid or full frame turbos. This intake system has been developed to provide the highest possible flow rate whilst achieving the lowest possible intake temperatures. Each component has been designed to give the turbo a smooth and clear flow path. The restrictive standard intake pipe with a diameter of 73 mm is replaced by an intake pipe with a larger diameter of 94 mm. The filter itself has an outer diameter of 192mm or 7.5? with a filter area of over 110,000mm^2. The patented Venturi housing is designed to provide the largest possible internal volume for the available space in the Golf engine bay and provides laminar flow to the turbo pipe. Finally, the duct seals the filter opening at the windscreen, but is not restricted by the standard intake alone. We have raised the front of the duct to now create an additional opening behind the bonnet, equivalent to an extra 7? diameter hole for the inlet to draw from. The resulting system can significantly outflow the stock airbox while keeping intake temperatures to a minimum with the sealed design. Dyno testing Our MK8 Golf intake has been independently tested by a renowned tuner in the UK, Regal Autosport. A MK8 Golf R was tested in original condition and with a tuning box. The tests were carried out on the same day, with the standard airbox being tested first and then the Eventuri. No other changes were made to the car. The first graph shows the results with a stock map. As can be seen, there is a measurable gain across the rev range of up to 12bhp. This gain is noticeable even in a standard vehicle on the road due to better throttle response and faster acceleration. The second diagram shows the results when using a tuning box that increases the flow requirement of the intake system. The tuning box was used for both the standard airbox and the Eventuri intake, with no changes made between tests. With a higher flow requirement, the stock airbox places a greater restriction on the turbo, which is evident by the significant increase achieved with the Eventuri fitted. We now have a power increase of up to 20 hp and 30 Nm across the entire rev range, which is even more noticeable on the road. We expect the gains to be even greater with higher tuning levels. The improvements are due to a combination of reasons: 1) The closed system keeps IAT levels low - the Golf's engine bay can heat up very quickly, so an open cone filter leads to an increase in IAT levels and therefore a loss of power. 2) The Venturi housing provides a smooth transition from the filter to the intake pipes, both of which are matched to an internal diameter of 94mm. This contributes to a more efficient operation of the turbo. 3) The entire system is made from pure pre-impregnated carbon fibre, which provides excellent insulation against heat and has smooth internal surfaces, unlike glass fibre, which has sharp resin lines. Parts certificate The manufacturer's specifications apply to installation. An existing certificate is no guarantee that the product can also be installed in the corresponding vehicle. A certificate is available for this product for the following regions and vehicles: * DE/AT: Vehicle registration document, field K --- CH/LI: Vehicle licence, field 24 Country Model Type approval* DE/AT Audi S3 (8Y) e1*2007/46*2060*.. DE/AT Audi TTS (FV/FVP/8S e1*2001/116*0369*.. DE/AT Cupra Ateca LCI e9*2007/46*6394*.. DE/AT Cupra Formentor e9*2007/46*4008*.. DE/AT Cupra Leon e9*2007/46*3167*.. DE/AT Skoda Octavia RS e8*2007/46*0355*.. DE/AT Skoda Superb e8*2007/46*0317*.. DE/AT Volkswagen Arteon R e1*2007/46*1725*.. DE/AT Volkswagen Golf 8 GTI e1*2007/46*2014*.. DE/AT Volkswagen Golf 8 GTI CS e1*2007/46*2014*.. DE/AT Volkswagen Golf 8R e1*2007/46*2014*.. DE/AT Volkswagen Tiguan R e1*2001/116*0450*.. DE/AT Volkswagen Tiguan R (AD1) e1*2007/46*0487*.. Compatible vehicles: VehicleVehicle typePowerEngine capacityEngine type Audi Q3 (F3)45 TFSI quattro180kW / 245hp1984cm³DNPA Cupra Formentor (KM)2.0 TSI180kW / 245hp1984cm³DNPA Cupra Leon (KL)2.0 TSI180kW / 245hp1984cm³DNPA Seat Tarraco (KN)2.0 TFSI 4Drive180kW / 245hp1984cm³DNPA Skoda Octavia IV (NX)RS 2.0 TFSI180kW / 245hp1984cm³DNPA Skoda KodiaqRS 2.0 TSI 4x4180kW / 245hp1984cm³DNPA VW Golf 8GTI 2.0 TSI180kW / 245hp1984cm³DNPA VW Tiguan II (AD)2.0 TSI 4motion180kW / 245hp1984cm³DNPA

The carbon replacement air intakes Twin Fin for the G8x were developed to match the channel lines of the SP1 G8X front splitter. With both the SP1 and Twin Fin ducts installed, you get the aggressive angles your front end needs.Our covers are a direct replacement, which means you can finally remove the honeycomb grille that is currently in front of the air ducts.These covers are made of pure pre-preg carbon, so the bumper adds minimal weight while providing the aggressive look you've been wanting. Details:- 100% pure pre-preg carbon fiber construction- OEM style fabric- High gloss finish- Fit guarantee- Mounts to the OEM front bumper using the original grille clip positions- with parts certificate according to §19.3 Compatible vehicles:- BMW G80 M3/Competition/CS Sedan (2021+)- BMW G81 M3 Competition Touring (2021+)- BMW G82 M4/Competition/CSL Coupe (2021+)- BMW G83 M4 Competition Convertible (2021+)Note: This is NOT an original BMW product!

The EVO III hose kit is suitable for the following vehicles:BMW 335d E90/91/92/93 (2005-2013) Optimize the performance and efficiency of your vehicle with our state of the art hose kit EVo 3. Designed to maximize airflow and minimize pressure loss, this kit offers a premium solution for enthusiasts looking to unlock the full potential of their vehicle. Optimized airflow: The aluminium charge air tube and adapter have been specifically designed to improve airflow and minimize pressure loss. This contributes to increased performance and improved engine response. High quality materials: Made from high quality aluminum and reinforced silicone, the components of this kit offer excellent heat resistance and durability, even under extreme conditions. Easy installation: The kit is supplied with all necessary hose clamps and fitting materials and is easy to install using standard hand tools. The precisely manufactured silicone hoses ensure a perfect fit and a reliable seal. Compatibility:This hose kit is exclusively compatible with our Wagner Tuning intercooler to ensure seamless integration. It is specially designed for 3 Series vehicles of the E-series. Scope of delivery:3 silicone hoses1 aluminium adapter (black anodized)1 aluminium charge air pipe (black anodized)6 hose clamps Note: Please note that the item image is for illustrative purposes only and the actual shape of the kit may differ slightly.