KW V4 coilover suspension | fits BMW M5 (F90/G30) incl. Competition/CS | 3A7200CB | 3A7200CC

Actuator for exhaust flap OEM part number: 18307851568 (18 30 7 851 568) Suitable for the following BMW models with exhaust flap: F80 F82 F83 F85 F86 F87N F90 F91 F92 F93 F95 F96 F97 F98 G01 G02 G05 G06 G14 G15 G16 G20 G21 G22 G23 G26 G30 G42 G82 G83

Here you get an original TitanTec sports air filter with all its advantages:- higher air flow rate- higher filter performance (even smaller particles are filtered)- The particles are trapped in the filter after intake and thus remain trapped until cleaning.- Washable and reusable filter- Increased air flow and therefore better combustion in the engine- No reduction in air flow over a minimum of 50,000 km- Sufficient air even at high engine speeds- more power- Better intake noise- Reduced fuel consumption Only TitanTec sports air filters use polyurethane as the edge material. Polyurethane is more resistant to petrol, vapours and the like. It has an ideal remoulding. This ensures that the edge of the filter is 100% sealed even when it is reinserted after cleaning. The edge surface is made from a single mould. With many other makes, pores in the edge material and joining surfaces where the edge is joined together often lead to a crack in the edge, which can result in unclean air being sucked into the engine. With paper filters, the air flow rate is significantly lower and decreases further after just a short period of use.In addition, paper filters must be disposed of after the specified mileage. TitanTec sports air filters last a lifetime. This is good for the environment and your wallet.Compared to TitanTec sports air filters, other washable cotton filters only filter much larger particles. Cleaning the filters:A TitanTec sports air filter has no oil residue and has 100% of its original performance again after cleaning.Cleaning is quick and easy.We recommend cleaning after 15,000-20,000 kilometres or once a year at the latest.The best time to clean the air filter is around the end of May or beginning of June, i.e. after the pollen count, as this is the time when the air filter is under the most strain.Under no circumstances should aggressive cleaning agents such as petroleum ether, cleaning petrol, brake cleaner etc. be used, as this can damage the material. Details: 1x set of panel filters (right/left) Length: 264 mm Width: 215 mm Compatible vehicles:BMW M5 (F90) 600 hp, 441 kW, 09/17 to 06/23 BMW M5 (F90) M5 Competition, 625 hp, 460 kW, 07/18 to 06/23 BMW M5 (F90) M5 CS, 635 hp, 467 kW, 03/21 to 02/22 BMW M5 (G90) M5 plug-in hybrid all-wheel drive, 727 hp, 535 kW, from 07/24 BMW M5 Touring (G99) M 5 plug-in hybrid all-wheel drive, 727 hp, 535 kW, from 10/24 BMW M8 Coupe (F92) M8, 600 hp, 441 kW, from 07/19 BMW M8 Coupe (F92) M8 Competition, 625 hp, 460 kW, from 07/19 BMW M8 Gran Coupe (F93) M8, 600 hp, 441 kW, from 11/19 BMW M8 Gran Coupe (F93) M8 Competition, 625 hp, 460 kW, from 11/19 BMW M8 Convertible (F91) M8, 600 hp, 441 kW, from 07/19 BMW M8 Convertible (F91) M8 Competition, 625 hp, 460 kW, from 07/19Note: This is NOT an original BMW product!

Facts: - replaces the main catalytic converter - with 200-cell stainless steel sports catalytic converter - Euro 6 compatible - for non-OPF vehicles - optionally with thermal insulation (with surcharge) - without approval in the area of the StVZO Compatible vehicles:VehicleVehicle typePower outputcubic capacityEngineYear of construction BMW 5 Series (F90)M5 441kW / 600PS4395ccS63 B44 B09.17 - Note: Depending on the software version, the engine control light may light up. We recommend adapting the software in this case.

Facts: - Catless - with thermal insulation - aggressive sound - no excessive noise under normal driving conditions - without approval in the area of the StVZO Compatible vehicles:VehicleVehicle typePowerCapacityEngine typeYear of construction BMW 5 Series (F90)M5 441kW / 600hp4395cm³S63 B44 B09.17 - 11.20 BMW 8 Series (F91/F92/F93)M8 441kW / 600hp4395cm³S63 B44 B09.17 - 11.20 Attention: Not for models manufactured after 11/2020! Note: Depending on the software version, the engine control light may light up. We recommend adapting the software in this case.*ATTENTION: Cat replacement pipes marked “without approval” are not permitted for use on public roads and are intended for racing purposes only! If you nevertheless install a product without approval in your vehicle and use it within the scope of the StVZO, you are liable to prosecution. Possible consequences that you can expect in this case: Expiry of the operating license according to §19 of the StVZO and a possible resulting immobilization of the vehicle. Other possible consequences, such as a charge of tax evasion, as well as possible investigations by the environmental authorities are at the discretion of the investigators.

Facts: - replaces the main catalytic converter - with 4x stainless steel sports catalytic converter - Euro 6 compatible - optionally with Thermo-Integral insulation (with surcharge) - with ECE approval*Compatible vehicles:VehicleVehicle typePower outputEngine capacityEngineYear of construction from BMW 5 Series (F90)M5 441kW / 600PS4395ccS63 B44 B2019 - BMW 5 Series (F90)M5 Competition460kW / 625PS4395ccS63 B44 B2019 - BMW 5 Series (F90)M5 CS467kW / 635PS4395ccS63 B44 B2019 - BMW 8 Series (F92)M8 441kW / 600PS4395ccS63 B44 B2019 - BMW 8 Series (F92)M8 Competition460kW / 625PS4395ccS63 B44 B2019 - BMW X5 (F95)M441kW / 600PS4395ccS63 B44 B2019 - BMW X5 (F95)M Competition460kW / 625PS4395ccS63 B44 B2019 - BMW X6 (F96)M441kW / 600PS4395ccS63 B44 B2019 - BMW X6 (F96)M Competition460kW / 625PS4395cm³S63 B44 B2019 - With combination certificate in conjunction with the Aulitzky Exhaust exhaust system, intercooler, intake and our power increase to 760PS.Note: Depending on the software version, the engine control light may light up. We recommend adapting the software in this case.Suitable for OE article number: 18328088820 Catalytic converter cyl. 1-4 18328088821 Catalytic converter cyl. 5-8 18329504708 Catalytic converter bottom cyl. 1-4 18329504709 Catalytic converter cyl. 5-8 *This downpipe has ECE approval so that it can be used within the scope of the StVZO without registration in the vehicle documents.

Facts: - Exhaust flaps with ceramic bearings - Electric flaps - Plug & Play driveable with original exhaust system - Approval/installation possible in conjunction with our downpipe - Cat/OPF back system - Made in Germany (Lake Constance) - with/without ECE approval (depending on choice of flap control)* Compatible vehicles:VehicleTypePowerEngine capacityEngineYear of construction BMW 5 Series (F90)M5 441kW / 600hp4395ccS63 B44 B09.17 - BMW 5 Series (F90)M5 Competition460kW / 625hp4395cm³S63 B44 B07.18 - BMW 5 Series (F90)M5 CS467kW / 635hp4395cm³S63 B44 B03.21 - BMW 8 Series (F92)M8 441kW / 600hp4395cm³S63 B44 B07.19 - BMW 8 Series (F92)M8 Competition460kW / 625hp4395cm³S63 B44 B07.19 - *ATTENTION! In conjunction with the standard or ECE flap control system (with type approval), this flap exhaust system has ECE approval so that it can be used legally within the scope of the StVZO without registration in the vehicle documents.The use of flap exhaust systems in conjunction with the race flap control (without approval) is not permitted for use on public roads and is only intended for racing purposes! If you nevertheless install a product without approval in your vehicle and use it within the scope of the StVZO, you are liable to prosecution. Possible consequences that you can expect in this case: Expiry of the operating licence in accordance with §19 of the StVZO and possible resulting immobilisation of the vehicle. Other possible consequences, such as a charge of tax evasion, as well as possible investigations by the environmental authorities are at the discretion of the investigators.

The Aulitzky Exhaust OPF-Deleter module is used to mechanically remove the OPF (gasoline particulate filter) without subsequent software adaptation.It is installed in the engine compartment and can be removed at any time without leaving any residue. - No error messages from the module - No detection possible using the manufacturers test device Notes:An OPF deleter is only there to suppress an error message from the catalytic converter or OPF monitoring.  This can appear if, for example, a modified downpipe or an export flap control is installed and the flaps are permanently open as a result.Caution:The OPF must still be installed.However, if the OPF is removed completely, the OPF offset cables are required in addition to the OPF deleter. (These are also available in the online store).1. after removing the OPF, the complete sensor system including all lines must still be connected to the exhaust system and be tight! Otherwise there will be error messages despite the OPF deleter and offset cable!2. for F8X M models, the package consisting of OPF deleter and OPF offset must be purchased from the outset when installing an export flap control system, otherwise error messages may still occur despite the OPF being installed! Compatible vehicles:VehicleVehicle typePowerEngine capacityEngine typeYear of constructionBMW 5er (F90)M5 441kW / 600hp4395cm³S63 B44 B06.21 - BMW 5er (F90)M5 Competition460kW / 625hp4395cm³S63 B44 B06.21 - BMW 5er (F90)M5 CS467kW / 635hp4395cm³S63 B44 B06.21 - Note: This product is NOT approved in the StVZO and is NOT intended for sale within the EU! This article is intended exclusively for show and motorsport purposes and must not be used/installed on public roads. If the component is installed on/in the vehicle, the operating license expires! For dealers only. No sale to end customers!

Function:- variable flap control of the original or retrofitted flap exhaust system- controllable via steering wheel buttons Compatible vehicles: VehicleTypePowerEngine capacityEngine typeYear of constructionBMW 5er (F90)M5 441kW / 600hp4395cm³S63 B44 B09.17 - BMW 5er (F90)M5 Competition460kW / 625hp4395cm³S63 B44 B07.18 - BMW 5er (F90)M5 CS467kW / 635hp4395cm³S63 B44 B03.21 - Note: This product is NOT StVZO approved and NOT intended for sale within the EU! This item is for show & motorsport purposes only and must not be used/installed on public roads. If the component is installed on/in the vehicle, the operating license expires! The pictures shown are examples.

Transform your F9X into a high-performance powerhouse with the BlackBoost cooling air intake system. Experience more power, style and driving dynamics with this premium upgrade. In the world of performance modifications, the airbox is one of the most important engine components you should upgrade. The factory airbox is very restrictive in terms of airflow and filter area. Our cooling air intakes are designed and engineered to overcome these factory restrictions and deliver the maximum airflow with the lowest possible temperatures given the space available. The BlackBoost Cold Air Intakes are designed to be flush with the bonnet of the vehicle and ensure a consistent seal with the rubber seals of the airbox, whilst also ensuring a large surface area for our 10.92cm (4.3 inch) Twin Flow Conical Filters to work properly. The BlackBoost Twin Flow filters have been specifically designed to maximise airflow and surface area. With a diameter of 10.92 cm (4.3 inches) and a height of 20.32 cm (8 inches), they are guaranteed to provide the best airflow and protection. The airboxes are laser-cut aluminium panels with highly complex CNC bends, assembled with stainless steel fasteners and finished with a high-quality black powder coating. The BlackBoost intake kit is a plug-and-play solution that works perfectly without further customisation and requires no additional software tuning. It also works smoothly in combination with turbo upgrades, downpipes, methanol injections etc. to unleash the necessary airflow and utilise the full capacity of the machine for those aiming for 1000+ WHP figures. Scope of delivery:- Powder coated airbox- 2x 10.92 cm (4.3 inch) twin high flow dry filters- 2x BlackBoost CFD developed filter adapters Key features:- Proven power increase from 8 to 30+ hp on production vehicles- Improved responsiveness across the entire rev range- Optimised airflow and increased volume range compared to standard equipment- Increased surface area of the filter elements- Can support airflow for 1000+ WHP configurations- Larger filter element surface area compared to OEM- Plug-and-play bolt-on installation- No ECU tuning required Compatible vehicles: BMW M5 (F90) 441kW/600hp 4395cm³ S63B44B (2017+) BMW M5 (F90) Competition 460kW/625hp 4395cm³ S63B44B (2017+) BMW M5 (F90) CS 467kW/635hp 4395cm³ S63B44B (2017+) BMW M8 (F91/F92/F93) 441kW/600hp 4395cm³ S63B44B (2019+) BMW M8 (F91/F92/F93) Competition 460kW/625hp 4395cm³ S63B44B (2019+)

Cold Air Intake System by BlackBoost. Precision-engineered performance upgrade for BMW M5 (F90) S63 4.4L V8 Twin-Turbo.

A high-end kit for a high-end car. The new F90 gets a new, innovative look. The new AERO body kit from 3DDesign for the F90 fits seamlessly into the familiar, discreetly aggressive race style of the 3DDesign lines. The iconic design is complemented by a perfect fit and the usual uncompromising quality. The real eye-catcher and centerpiece of the body kit - an carbon diffuser that is uncompromisingly and aggressively designed as a direct replacement part. The clear lines and curved shape fit perfectly into the image of the F90. Three inner fins not only ensure a racy look, but also optimum airflow. The F90 M5 carbon diffuser comes in two parts and can also be purchased separately. A performance diffuser for the F90, which is also a real visual upgrade! Pure luxury! Compatible vehicles:BMW 5 (G30, F90) M5 2017-2023BMW 5 (G30, F90) M5 Competition 2018-2023

Dry Carbon Competition diffuser for the rear center diffuser of the F90. Designed to mount directly to the factory lower mounting position for quick and easy installation. The rear diffuser features durable and precise plastic mounting positions and is manufactured using autoclave technology for ultimate lightweight, high durability and precise fitment. Compatible vehicles:BMW 5 (G30, F90) M5 2017-2023BMW 5 (G30, F90) M5 Competition 2018-2023

A high-end kit for a high-end car. The new F90 gets a new, innovative look. The new AERO body kit from 3DDesign for the F90 fits seamlessly into the familiar, discreetly aggressive racing style of the 3DDesign lines. The iconic design is complemented by a perfect fit and the usual uncompromising quality. As with the F10, the front lip comes with a maximum amount of carbon fibre. Above the aggressive centreboard with aero lift slits, the lip extends into the air intakes on the right and left. A performance front lip for the F90 that is also a real visual upgrade! Pure luxury! Compatible vehicles:BMW 5 (G30, F90) 518 d 2018-2020BMW 5 (G30, F90) 518 d mild hybrid 2020-2023BMW 5 (G30, F90) 520 d 2016-2023BMW 5 (G30, F90) 520 d Mild-Hybrid 2019-2023BMW 5 (G30, F90) 520 d Mild-Hybrid xDrive 2019-2023BMW 5 (G30, F90) 520 d xDrive 2016-2023BMW 5 (G30, F90) 520 i 2017-2023BMW 5 (G30, F90) 520 i Mild-Hybrid 2020-2023BMW 5 (G30, F90) 525 d 2017-2019BMW 5 (G30, F90) 530 d 2016-2020BMW 5 (G30, F90) 530 d Mild-Hybrid 2020-2023BMW 5 (G30, F90) 530 d Mild-Hybrid xDrive 2020-2023BMW 5 (G30, F90) 530 d xDrive 2016-2020BMW 5 (G30, F90) 530 e Plug-in Hybrid 2017-2023BMW 5 (G30, F90) 530 e Plug-in Hybrid xDrive 2017-2023BMW 5 (G30, F90) 530 i 2016-2020BMW 5 (G30, F90) 530 i Mild-Hybrid 2020-2023BMW 5 (G30, F90) 530 i Mild-Hybrid xDrive 2020-2023BMW 5 (G30, F90) 530 i xDrive 2016-2023BMW 5 (G30, F90) 540 d Mild-Hybrid xDrive 2020-2023BMW 5 (G30, F90) 540 d xDrive 2017-2020BMW 5 (G30, F90) 540 i 2016-2020BMW 5 (G30, F90) 540 i Mild-Hybrid 2020-2023BMW 5 (G30, F90) 540 i Mild-Hybrid xDrive 2020-2023BMW 5 (G30, F90) 540 i xDrive 2016-2020BMW 5 (G30, F90) 545 e Plug-in Hybrid xDrive 2020-2023BMW 5 (G30, F90) M 550 d xDrive 2017-2020BMW 5 (G30, F90) M 550 i xDrive 2017-2023BMW 5 (G30, F90) M5 2017-2023BMW 5 (G30, F90) M5 Competition 2018-2023

AutoTecknic's vision is to develop the most advanced, innovative and unique products on the market to meet the needs of the most demanding customers. The lightweight carbon fiber aerodynamic products are uniquely designed to enhance the original design of your vehicle. The central design philosophy "understand functional elegance" takes the sporty appearance of your vehicle to a new level. Quality products characterize the AutoTecknic brand. Every single part must pass strict quality controls before it reaches your vehicle. Customers expect nothing less than the best parts from AutoTecknic, so naturally we expect nothing less. AutoTecknic's autoclaved pre-preg carbon fiber structure gives the product superior stiffness, strength and durability compared to traditional handmade carbon fiber composites. AutoTecknic Dry Carbon Center Front Lip for the F90 is both highly visible and highly functional. Compatible vehicles:BMW 5 (G30, F90) M5 2017-2023BMW 5 (G30, F90) M5 Competition 2018-2023

Dry Carbon Performante Aero Splitter for the F90. Designed to seamlessly follow the curvature and mount directly onto the lower bumper mount for quick and easy installation. The Dry Carbon Aero Splitters are manufactured using signature autoclave technology with pre-preg 3K twill carbon fibre and finished with UV protected high gloss clear coat for the ultimate lightweight, durable and snug fitting splitters. The name Dry Carbon comes from the manufacturing process. Dry Carbon is formed by using a pre-preg or impregnated piece of carbon material. This piece of carbon is first placed in a mould and then placed in a sealed vacuum (autoclave) to cure properly. This particular method creates the least amount of waste and forms a lighter version of carbon than the wet method. The autoclave vacuum process for producing dry carbon means that fewer pinholes and virtually no air pockets form in the carbon. Dry carbon is the highest quality version of carbon products produced. AutoTecknic Dry Carbon Performante Aero Splitters are both highly visible and highly functional. Compatible vehicles:BMW 5 (G30, F90) M5 2017-2023BMW 5 (G30, F90) M5 Competition 2018-2023

Facts: Acceleration time: 60-130mph Reduced by 0.22 seconds Max. Flow rate per airbox at 28? H2O: Standard 620 CFM, Eventuri 736 CFM Material: Carbon Manufacturer: Eventuri Parts certificate: A certificate is available for this product for certain regions and vehicles (details below) The F90 Eventuri intake system has been developed through extensive real-world testing and airflow simulation analyses. Now in the updated V2 design, it features sealed filter housings to maintain a more stable IAT even when stationary. The new covers that seal the housings, in conjunction with our blade and shield combination, provide unrestricted airflow while maintaining low IATs through cold air saturation. Our large front air scoops channel ambient air directly into the intake area, ensuring that the engine does not suffer from heat soak. In addition, our gold-coloured, heat-reflecting shields have integrated flow guides that direct the ambient air from the blades into the filters. We have also managed to increase the cross-sectional area of the inlet pipe by over 30% compared to the standard inlet, as it passes through the openings in the struts. The Eventuri difference The F90 Eventuri system uses our patented carbon fibre housings with our bespoke Gen 2 filters, providing an aerodynamically efficient airflow path from the filter to the turbos. Not just another cone filter with a heat shield, but a unique design that creates the Venturi effect and maintains laminar flow conditions to reduce turbo drag. Internal volume Another important design feature of the inlet housings is the internal volume of the tubes as they pass through the struts. On the F90, the airbox system must pass through an oval opening in the strut brace on each side before reaching the turbo inlets. We have managed to increase the internal size of our inlets at this junction, resulting in more available volume for the turbos and therefore less restriction. The increase in cross-sectional area between the Eventuri and the standard airbox is 31% as follows: Inner cross-sectional area of the intake pipe at the strut brace: Standard airbox pipe = 6487 mm² Eventuri intake pipe = 8497 mm² Each intake system consists of: 2 x carbon fibre venturi housings with integrated pipes 2 x customised high-performance Generation 2 filters 2 x carbon fibre filter covers 2 x aluminium intake covers 2 x carbon fibre air scoops 2 x laser-cut heat shields, lined with gold heat reflective material 2 x laser-cut air ramps integrated into the heat shields High-quality silicone couplings and OEM hose clamps Parts certificate The manufacturer's specifications apply for installation. An existing certificate is no guarantee that the product can also be installed in the corresponding vehicle. A certificate is available for this product for the following regions and vehicles: * DE/AT: Vehicle registration document, field K --- CH/LI: Vehicle licence, field 24 Country Model Type approval* DE/AT BMW M5 e1*2007/46*1828*.. DE/AT BMW M5 Competition e1*2007/46*1828*.. DE/AT BMW M8 e1*2007/46*2019*.. DE/AT BMW M8 Competition e1*2007/46*2019*.. Compatible vehicles:VehicleTypePowerEngine capacityEngine typeYear of construction BMW 5 Series (F90)M5 441kW / 600hp4395cm³S63 B44 B09.17 - BMW 8 Series (F91/F92/F93)M8 441kW / 600hp4395cm³S63 B44 B07.19 -

The intercooler for F90 and F92 knows how to impress and will certainly not disappoint you. ColourThe intercooler comes in a classic, appealing black that matches any vehicle colour and rounds off the overall appearance of your car. InstallationThe installation of our intercooler is as simple as the original part. It's a direct replacement, which means you don't have to follow complicated instructions or buy additional parts. MaterialThe intercooler is made of robust and durable aluminium. This material is lightweight yet highly resistant to high temperatures, making it ideal for the requirements of an intercooler. Compatible vehicles:BMW 5 (G30, F90) M5 2017-2023BMW 5 (G30, F90) M5 CS 2021-2022BMW 5 (G30, F90) M5 Competition 2018-2023BMW 8 Convertible (G14, F91) M8 since 2019BMW 8 Convertible (G14, F91) M8 Competition Since 2019BMW 8 Coupe (G15, F92) M8 Since 2019BMW 8 Coupe (G15, F92) M8 Competition Since 2019BMW 8 Gran Coupe (G16, F93) M8 Since 2019BMW 8 Gran Coupe (G16, F93) M8 Competition Since 2019

KW V4 coilover suspension - State of the Art With the new KW V4 with its stainless steel or aluminium coilover struts, you give your super sports car the necessary reserves to further increase the driving dynamics. The three-way adjustable high-performance dampers with their independent adjustment of the rebound, low-speed and high-speed compression damping are based on the successful racing technology of the multiple overall winner of the ADAC Zurich 24h Race Nürburgring and, depending on the vehicle-specific version, have aluminium support bearings. The new KW V4 is developed exclusively for selected high-performance vehicles, which can be moved more safely at the limits of driving dynamics thanks to our KW suspension technology. - 3-way adjustable high-performance dampers with stainless steel coilover struts - Separate and independent damper adjustment in: - Rebound damping with 16 exact clicks + (firmer) / - (more comfortable) - Low-speed compression damping with 6 exact clicks + (firmer) / - (more comfortable) - High-speed compression damping with 14 exact clicks + (firmer) / - (more comfortable) - Two basic set-ups ex works with comfort setting and performance setting - Depending on the vehicle, aluminium support bearings are an integral part of the scope of delivery Please note the conditions and instructions for this product: - VA + HA height-adjustable (coilover struts) - Dampers have easy-to-use adjustment wheels. Due to the design, the rebound stage can only be adjusted when the piston rod is accessible. - Vehicles with electronic damper control must be decommissioned. Electronics kit for decommissioning is included in the scope of delivery for the “YES” article variant. - Variant 4 / Variant 5 Suspension struts / dampers made of aluminium or combined on each axle made of aluminium and stainless steel Technical information: Lowering VA/HA (mm): 15-30/10-30 Design: V4 Adjustable rebound and compression damping Material: Aluminium Adjustment VA/HA: thread/thread Approval: Parts certificate (§19.3) Compatible vehicles: Manufacturer Model Version Body Fuel Performance Displacement Cylinder Drive BMW 5 Series (G30, F90) F5LM, G5L 09/2016- M5 notchback petrol 441 KW 4395 ccm 8 all-wheel drive BMW 5 Series (G30, F90) F5LM, G5L 09/2016- M5 Competition notchback petrol 460 KW 4395 ccm 8 all-wheel drive BMW 5 Series (G30, F90) F5LM, G5L 09/2016- M5 CS notchback petrol 467 KW 4395 ccm 8 all-wheel drive

H&R lowering springs for F90 models from 2018 (VA20-30/HA20-30mm) H&R sports spring kits are the ideal solution if you want to optimize the handling of your vehicle and achieve a sporty look while maintaining the standard driving comfort. Details:Lowering VA/HA Sedan: 30/30mmLowering VA/HA Competition Sedan: 20/20mmSuspension: for vehicles with electric damper controlType of approval: with general operating permit (ABE) Product advantages:Sporty look and performanceLowering of the vehicle's center of gravityLinear or progressive suspension characteristicsCan be combined with standard or retrofit dampersOptimized driving dynamicsSurface protection through powder coatingMade in Germany Compatible vehicles:BMW M5 Sedan F90 type F5LM only with adaptive damper control 2018- front axle 30mm / rear axle 30mmBMW M5 Competition Sedan F90 type F5LM, only with adaptive damper control 2018- front axle 20mm / rear axle 20mm

Eibach Pro-Kit performance suspension springs for front and rear axle E10-20-041-01-22 The Eibach Pro-Kit lowering springs are the ideal solution for your vehicle, as the kit lowers the centre of gravity, reduces rebound when accelerating, reduces body roll when cornering and dips when braking. As a result, understeer and oversteer no longer occur. Lowering the vehicle with the Pro-Kit springs reduces the standard distance between the tyres and the wheel arch and gives the vehicle a sporty look. In addition, the handling of the vehicle is maximised. The Eibach Pro-Kits are designed by Eibach suspension engineers and testing experts to deliver a combination of sporty looks and performance without compromising on safety or ride quality. - Developed and tested for combination with standard and aftermarket dampers- Component of the Eibach Pro system- Top performance handling- Lowers the vehicle's centre of gravity by up to 40 mm (depending on the vehicle)- Spring design for traction and attraction- Progressive suspension characteristics- Performance handling- ABE or parts certificate Note: Only for vehicles without levelling control. Information:- Lowering front axle: approx. 25mm- Lowering rear axle: approx. 20mm- Type of approval: with expert opinion- Illustration may differ from the original Compatible vehicles:- Axle load front axle: up to 1215kg- Axle load rear axle: up to 1260kg- EC type approval number: e1*2007/46*1688*..- Only for vehicles without levelling system BMW 5 (F90) M5 441kW / 600PS 7909-ABWBMW 5 (F90) M5 Competition 460kW / 625hp 7909-ABV

The RKP carbon mirror caps for the F90 are definitely a highlight on your vehicle.They impress with their perfect fit and easy installation. Details:- Flawless fit- Extremely light- Clear lacquered and high-gloss polished Compatible vehicles:BMW M5 441kW/600PSBMW M5 Competition 460kW/625PS

The exterior mirror covers in glossy pre-preg carbon fibre give your standard mirror units a more aggressive and premium look.Quick and easy to fit, they are a styling option with perfect value for money to enhance the road presence of your vehicle. Unlike normal carbon fibre, pre-preg carbon is reinforced to increase strength and durability. It can also be a staggering 70% lighter than other carbon fibre options.Prepreg carbon is far more uniform than other carbon types, meaning the likelihood of imperfections is drastically reduced. The manufacturing process eliminates unwanted air bubbles and results in a perfectly smooth and high-gloss finish. Details:- 100% pure prepreg carbon fibre construction- OEM-style weave- High gloss finish- Guaranteed fit- registration free Scope of delivery:- 1x pair of mirror caps Compatible vehicles:BMW F90 M5 SaloonBMW F91 M8 ConvertibleBMW F92 M8 CoupeBMW F93 M8 Gran Coupé Note: This is NOT an original BMW product!

Facts:- Plug & Play installation using illustrated installation instructions- Special wiring harness for your vehicle- High-quality electronics “Made In Germany”- Electronic components with product qualification for motor vehicles according to AEC-Q100 installed- Support from us as co-developer and manufacturer Scope of delivery:The scope of delivery includes the motorsport add-on module, an engine-specific wiring harness, illustrated installation instructions in DE/EN and a BYPASS connector, which you can use to restore your vehicle to series production. Compatible vehicles: VehicleVehicle typePowerEngine capacityEngine typeYear of constructionBMW 5er (F90)M5 CS467kW / 635hp4395cm³S63 B44 B03.21 - LEGAL INFORMATION: THE INSTALLATION OF ADDITIONAL ELECTRONICS IS A STRUCTURAL MODIFICATION TO THE MANUFACTURER'S ELECTRONICS. WITHOUT REGISTRATION IN THE VEHICLE DOCUMENTS BY MEANS OF AN INDIVIDUAL CERTIFICATE FROM TÜV; DEKRA OR OTHER RECOGNIZED TESTING INSTITUTES, THE INSTALLATION WILL INVALIDATE THE OPERATING LICENSE. IF USED ON PUBLIC ROADS, THIS WILL RESULT IN THE LOSS OF INSURANCE COVER. WE DO NOT CURRENTLY HAVE A PARTS CERTIFICATE FOR YOUR VEHICLE. THEREFORE, THIS SYSTEM IS EXCLUSIVELY SUITABLE FOR MOTORSPORT. ATTENTION: IF YOU USE THE ADDITIONAL ELECTRONICS, YOU MAY LOSE YOUR WARRANTY CLAIMS AGAINST THE SELLER OR WARRANTY CLAIMS AGAINST THE MANUFACTURER. IF YOU HAVE ANY FURTHER QUESTIONS, PLEASE DO NOT HESITATE TO CONTACT US!

Compatible vehicles:BMW F90 M5 441KW/600hp (2017+)BMW F90 M5 Competition 460KW/625hp (2018+)BMW F90 M5 CS 467KW/635hp (2021+)BMW F91/92/93 M8 441KW/600hp (2019+) Boost your model's performance to a new level with the Wagner Tuning high-performance intercooler! The 4.4-litre V8 biturbo engine (S63 B44T4) has an indirect charge air cooling circuit in which the charge air is cooled by a water-cooled charge air cooler. With our innovative high-performance intercooler from Wagner Tuning, you can replace the original intercooler and experience an impressive increase in performance. Our high-performance intercooler has a new type of performance mesh with dimensions of 192 mm x 156 mm x 128 mm. It has been specially developed for the high demands of the engine and offers an incredible 75 % more external mesh volume compared to the standard intercooler. The optimised ratio between the inner and outer cooling surface ensures maximum heat transfer and optimum internal airflow. The cast aluminium end boxes were designed using the latest CAD technology and optimised using CFD simulations. The result is outstanding cooling properties with minimal back pressure, ensuring optimum cooling of the supercharged air with a significant increase in performance. This kit is ideally suited even for demanding racing. To ensure a long-lasting cooling effect, all Wagner Tuning intercoolers are equipped with a thermally conductive anti-corrosion coating. Installation of the system is uncomplicated thanks to our detailed installation instructions and is carried out in plug & play style. Advantages:- Significantly improved cooling performance- More power and torque for your engine- Mechanical relief of the turbocharger- Additional WMI ports- 100 % pressure resistance- 100 % plug-and-play- Up to 4 years warranty Mains dimensions OEM intercooler:152 mm x 143 mm x 100 mmV = 2.19 litres Mains dimensions Wagner Tuning intercooler:192 mm x 156 mm x 128 mmV = 3.83 litres (+75%) Scope of delivery:2 intercoolers5 silicone air hoses1 mounting material Attention: Not authorised in the area of the StVZO.

To increase strength and durability, prepreg carbon fibre is reinforced in contrast to normal carbon fibre and can still be 70% lighter than other carbon options. A decisive advantage in terms of weight saving. Prepreg carbon fibre is far more consistent in quality, so the likelihood of imperfections is greatly reduced. The manufacturing process eliminates unwanted air bubbles and results in a perfectly smooth and high-gloss finish. Key features:- 100% pure prepreg carbon fibre- OEM style weave- High gloss finish- Fitment guarantee- 1 year warranty - With parts certificate according to §19.3 Scope of delivery:1x performance front splitter made of glossy prepreg carbon fiber incl. mounting material Compatible vehicles:BMW G80 M3 Sedan (2021+)BMW G80 M3 Competition Sedan (2021+)BMW G81 M3 Touring (2023+)BMW G81 M3 Competition Touring (2023+)BMW G82 M4 Coupe (2021+)BMW G82 M4 Competition Coupe (2021+)BMW G83 M4 Convertible (2021+)BMW G83 M4 Competition Convertible (2021+) Note: This is NOT an original BMW product!

KW V4 Clubsport coilover suspension incl. support bearings incl. decommissioning for electric dampers With an uncompromising technology transfer from racing to the road, the KW Clubsport coilovers are convincing. The KW Clubsport coilovers convince with their uncompromising combination of high-end racing technology with maintenance-free KW original equipment components and expertises. This gives you the ideal accessories to realise the full potential of your sports car at trackdays, sports driver training courses, tourist drives on Grand Prix circuits and on the Nürburgring Nordschleife. Developed for the toughest racetrack in the world: the Nürburgring Nordschleife Even in their basic set-up, KW Clubsport coilovers are tuned to the different track surfaces, steep bends, jumps and chicanes of the 20.8 kilometre long Nürburgring Nordschleife. After all, as one of the most successful suspension manufacturers and suppliers in motorsport, we are at home on the Nordschleife. In the VLN Endurance Championship alone, we equip over 70 racing teams and, as a suspension manufacturer, have been able to support six overall victories at the ADAC Zurich 24h Race Nürburgring in ten years. The winner of the ADAC GT Masters 2011 also relies on our racing expertise, from which the KW Clubsport coilovers benefit. The basic setup of the KW V3 Clubsport and KW V4 Clubsport with separate expansion tank, which is perfectly adapted to the Nordschleife, allows you to customise your sports car even more individually to the desired sports tyre setup thanks to the numerous adjustment options. KW V4 Clubsport coilover suspension The vehicle-specific basic setup of the KW V4 Clubsport, developed in numerous test and measurement drives on the Nordschleife and the KW 7-post driving dynamics test bench, can be further adapted to your wheel loads, vehicle weight and the modified body stiffness, for example with a bolted cage, welded-in safety cell or strut braces, using the click adjustment. Similar to the KW Competition racing suspensions used in international motorsport, the KW V4 Clubsport coilover suspension allows the compression damping to be fine-tuned separately in the low-speed and high-speed range. The click adjustment of the patented KW two-valve control takes place directly on the expansion tank. You can vary the low-speed compression damping by hand with six precise clicks on the purple-coloured adjustment wheel. The gold-coloured adjustment wheel underneath allows you to change the high-speed compression stage of the recommended basic setup for your track day with 14 exact clicks. Independently of this, you still have 16 clicks at your disposal to noticeably adjust the rebound setting. If you want to tune the KW V4 Clubsport coilover suspension, which is available with an expert opinion, more comfortably for your journey to the Nordschleife or other race track for driving on the motorway, simply reduce the rebound forces via the rebound damping. - freely adjustable damping technology with 16 precise clicks in the rebound stage - adjustable compression damping with 6 clicks in the low-speed range and 14 exact clicks in the high-speed range - infinitely variable lowering - Tested adjustment range - high-quality components for a long service life - unique, independently acting damping force adjustment available with aluminium Unibal support bearings for technically sensible applications Setup: Application range and damper tuning The KW V4 Clubsport coilover suspensions impress with their vehicle-specific setup for trackday events on the Nürburgring Nordschleife, as well as the possibility of quickly adapting these suspensions to other racetracks and individual performance sports cars. Please note the conditions and instructions for this product: - VA + HA height-adjustable (VA coilover struts, HA springs with height adjustment + dampers) - Dampers have easy-to-use adjustment wheels. Due to the design, the rebound stage can only be adjusted when the piston rod is accessible. - Electronic damper control must be deactivated. Electronic kit for deactivation is included in the scope of delivery. - Clubsport suspension with support bearing: only available with VA support bearing Technical information: Lowering VA/HA (mm): 20-45/20-45 Version: V4 Clubsport Height adjustment: Rebound and compression damping Material: Stainless steel Adjustment VA/HA: thread/thread Approval: Parts certificate (§19.3) Compatible vehicles: Manufacturer Model Version Body Fuel Performance Displacement Cylinder Drive BMW 2 Series Coupe (F22, F87) 1C, M3 10/2012- M2 CS Coupe Petrol 331 KW 2979 ccm 6 Rear-wheel drive

AutoTecknic carbon seat cover suitable for F80 | F82 | F87 Competition Compatible vehicles:BMW 2 Coupe (F22, F87) M2 Competition 2018-2021BMW 3 (F30, F80) M3 2014-2018BMW 3 (F30, F80) M3 CS 2018-2018BMW 3 (F30, F80) M3 Competition 2016-2018BMW 4 Convertible (F33, F83) M4 2014-2020BMW 4 Convertible (F33, F83) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 2014-2020BMW 4 Coupe (F32, F82) M4 CS 2017-2019BMW 4 Coupe (F32, F82) M4 Competition 2016-2020BMW 4 Coupe (F32, F82) M4 GTS 2016-2019

The Wagner Tuning intercooler kit EVO III Competition fits the following vehicles with N54 & N55 engines:BMW 335 (x)i E90/E91/E92/93 2006-2011 (without ACC)BMW 335is E92 2009-2013 (without ACC)BMW 135i E82/E88 2007-2013 (without ACC / not in combination with M-Performance front bumper)BMW 1 SeriesM E82 2011-2013 (without ACC) Prepare to push the performance limits of your vehicle with our EVO 3 high performance intercooler kit. Designed to meet the demanding requirements of high performance tuning levels, this kit will provide you with an impressive level of performance enhancement and cooling. Measuring 510mm x 303mm x 180mm (stepped 20.65L), our high performance intercooler offers an impressive 162% larger flow area and a whopping 182% more charge air volume compared to the stock intercooler. This means a significant improvement in the cooling capacity and performance of your vehicle. At the heart of this intercooler is our high quality Tube Fin mesh with internal turbulators. This mesh ensures efficient heat transfer and optimizes airflow for maximum cooling. Despite its impressive size, the intercooler only weighs a light 13.2kg. The end boxes of the intercooler are made of cast aluminium and have been optimized with the help of flow analyses in the CFD system. This guarantees outstanding cooling performance with minimal back pressure. The inlets and outlets of the intercooler have been enlarged to Ø70mm to ensure maximum air flow. Our EVO 3 kit includes everything you need for installation, including reinforced silicone hoses. Replacement with the standard intercooler is simple and straightforward (plug-and-play). The anti-corrosion coating with heat conduction properties ensures long-lasting and optimum cooling. This kit was developed for the highest performance requirements and is tested and pressure-stable up to 6 bar. We place great emphasis on quality and constantly monitor our products to ensure they meet the highest standards. Prepare to dominate the road and take your vehicle to a new level of performance. With our EVO 3 high-performance intercooler kit, you are guaranteed breathtaking driving experiences. Advantages of the Wagner Tuning intercooler:- improved cooling performance- 162% larger inflow area- 182% more charge air volume- Inlets and outlets of the intercooler have been extended to Ø70mm- Plug & Play Scope of delivery:1 intercooler2 silicone hoses1 aluminum adapter1 mounting material1 assembly instructionAttention: Not approved in the area of the StVZO.

KW coilover suspension DDC “Plug & Play” The “Plug & Play” solution for vehicles that have a standard electronic damper adjustment. KW also offers you the possibility to combine the active standard damper control of your sporty vehicle with the stainless steel KW DDC Plug & Play coilover suspension. In this way, you can continue to use the existing active damper control in your car such as VW Scirocco, VW Golf VI, VW Passat, BMW and other models in conjunction with a stepless lowering. The best thing about it: Apart from replacing the adaptive standard suspension with the KW DDC Plug & Play coilover suspension, no further conversion steps or even modifications to the on-board electronics are necessary. The adaptive KW dampers are simply connected to the original connectors of your car manufacturer via the KW DDC plug connection. The standard control unit then takes over the regulation and control of the KW DDC Plug & Play coilover suspension. Perfect symbiosis of an OEM control unit with the advantages of an adaptive KW coilover suspension Our suspension technology is compatible with the electronics of various car manufacturers. This means that the adaptive KW DDC Plug & Play coilover suspension is immediately recognized by the on-board electronics. All displays and controls of your standard vehicle remain fully functional and combine the advantages of an adaptive damping system with the stylish and sporty lowering of a high-quality KW coilover suspension. Due to the exclusive use of rust-free stainless steel and durable components, the functionality of the rust-free KW coilovers is maintained under all weather conditions. Thanks to the dirt-resistant trapezoidal thread and the polyamide threaded ring, adjustment is also possible after a snowy winter, for example. No oxidation occurred on the KW threaded spring legs during a salt spray test. This means that the adjustment of the stepless lowering is not affected even after years. - the plug & play solution for sportiness or more ride comfort at the touch of a button with outstanding looks thanks to stepless lowering - Compatible with the standard suspension control unit - Vehicle-specific damper setups such as Comfort / Normal / Sport - Operation via series buttons in the interior Please note the conditions and instructions for this product: - VA + HA height-adjustable (VA coilover struts, HA springs with height adjustment + damper) - Only for vehicles with electronic damper control Technical information: Product line: Street Performance Lowering VA/HA (mm): 25-55/30-60 Design: DDC - Plug & Play Hardness adjustment: Rebound and compression Material: Stainless steel Adjustment VA/HA: Thread/thread Approval: Parts certificate (§19.3) Compatible vehicles: Manufacturer Model Version Body Fuel Performance Displacement Cylinder Drive BMW 3 Series (F30, F80) 3-HY, 3L, M3, M3 GTS 11/2011-10/2018 320 d xDrive notchback diesel 120 KW 1995 ccm 4 all-wheel drive BMW 3 Series (F30, F80) 3-HY, 3L, M3, M3 GTS 11/2011-10/2018 320 d xDrive notchback diesel 140 KW 1995 ccm 4 all-wheel drive BMW 3 Series (F30, F80) 3-HY, 3L, M3, M3 GTS 11/2011-10/2018 320 i xDrive notchback petrol 134 KW 1997 ccm 4 all-wheel drive BMW 3 Series (F30, F80) 3-HY, 3L, M3, M3 GTS 11/2011-10/2018 320 i xDrive notchback petrol 135 KW 1997 ccm 4 all-wheel drive BMW 3 Series (F30, F80) 3-HY, 3L, M3, M3 GTS 11/2011-10/2018 320 i xDrive notchback petrol 135 KW 1998 ccm 4 all-wheel drive BMW 3 Series (F30, F80) 3-HY, 3L, M3, M3 GTS 11/2011-10/2018 328 i xDrive notchback petrol 179 KW 1997 ccm 4 all-wheel drive BMW 3 Series (F30, F80) 3-HY, 3L, M3, M3 GTS 11/2011-10/2018 330 d xDrive notchback diesel 190 KW 2993 ccm 6 all-wheel drive BMW 3 Series (F30, F80) 3-HY, 3L, M3, M3 GTS 11/2011-10/2018 330 d xDrive notchback diesel 210 KW 2993 ccm 6 all-wheel drive BMW 3 Series (F30, F80) 3-HY, 3L, M3, M3 GTS 11/2011-10/2018 330 i xDrive notchback petrol 185 KW 1998 ccm 4 all-wheel drive BMW 3 Series (F30, F80) 3-HY, 3L, M3, M3 GTS 11/2011-10/2018 335 d xDrive notchback diesel 230 KW 2993 ccm 6 All-wheel drive BMW 3 Series (F30, F80) 3-HY, 3L, M3, M3 GTS 11/2011-10/2018 335 i xDrive notchback petrol 225 KW 2979 ccm 6 All-wheel drive BMW 3 Series (F30, F80) 3-HY, 3L, M3, M3 GTS 11/2011-10/2018 335 i xDrive notchback petrol 240 KW 2979 ccm 6 all-wheel drive BMW 3 Series (F30, F80) 3-HY, 3L, M3, M3 GTS 11/2011-10/2018 335 i xDrive notchback petrol 250 KW 2979 ccm 6 all-wheel drive BMW 3 Series (F30, F80) 3-HY, 3L, M3, M3 GTS 11/2011-10/2018 340 i xDrive notchback petrol 240 KW 2998 ccm 6 all-wheel drive BMW 3 Series (F30, F80) 3-HY, 3L, M3, M3 GTS 11/2011-10/2018 340 i xDrive notchback petrol 265 KW 2998 ccm 6 all-wheel drive BMW 4 Series Coupe (F32, F82) 3C, M3, M3 GTS 07/2013-06/2020 420 d xDrive Coupe Diesel 120 KW 1995 ccm 4 all-wheel drive BMW 4 Series Coupe (F32, F82) 3C, M3, M3 GTS 07/2013-06/2020 420 d xDrive Coupe Diesel 140 KW 1995 ccm 4 all-wheel drive  BMW 4 Series Coupe (F32, F82) 3C, M3, M3 GTS 07/2013-06/2020 430 d xDrive Coupe Diesel 190 KW 2993 ccm 6 All-wheel drive BMW 4 Series Coupe (F32, F82) 3C, M3, M3 GTS 07/2013-06/2020 430 d xDrive Coupe Diesel 210 KW 2993 ccm 6 All-wheel drive BMW 4 Series Coupe (F32, F82) 3C, M3, M3 GTS 07/2013-06/2020 430 i xDrive Coupe Petrol 183 KW 1998 ccm 4 All-wheel drive BMW 4 Series Coupe (F32, F82) 3C, M3, M3 GTS 07/2013-06/2020 435 d xDrive Coupe Diesel 230 KW 2993 ccm 6 All-wheel drive BMW 4 Series Coupe (F32, F82) 3C, M3, M3 GTS 07/2013-06/2020 435 i xDrive Coupe Petrol 225 KW 2979 ccm 6 All-wheel drive BMW 4 Series Coupe (F32, F82) 3C, M3, M3 GTS 07/2013-06/2020 435 i xDrive Coupe Petrol 250 KW 2979 ccm 6 All-wheel drive BMW 4 Series Coupe (F32, F82) 3C, M3, M3 GTS 07/2013-06/2020 440 i xDrive Coupe Petrol 240 KW 2998 ccm 6 All-wheel drive BMW 4 Series Coupe (F32, F82) 3C, M3, M3 GTS 07/2013-06/2020 440 i xDrive Coupe Petrol 265 KW 2998 ccm 6 All-wheel drive