Lowering springs 30/30mm / 20/20mm | fits BMW M5 Sedan incl. Competition (F90) | 28686-1 | H&R

Actuator for exhaust flap OEM part number: 18307851568 (18 30 7 851 568) Suitable for the following BMW models with exhaust flap: F80 F82 F83 F85 F86 F87N F90 F91 F92 F93 F95 F96 F97 F98 G01 G02 G05 G06 G14 G15 G16 G20 G21 G22 G23 G26 G30 G42 G82 G83

Here you get an original TitanTec sports air filter with all its advantages:- higher air flow rate- higher filter performance (even smaller particles are filtered)- The particles are trapped in the filter after intake and thus remain trapped until cleaning.- Washable and reusable filter- Increased air flow and therefore better combustion in the engine- No reduction in air flow over a minimum of 50,000 km- Sufficient air even at high engine speeds- more power- Better intake noise- Reduced fuel consumption Only TitanTec sports air filters use polyurethane as the edge material. Polyurethane is more resistant to petrol, vapours and the like. It has an ideal remoulding. This ensures that the edge of the filter is 100% sealed even when it is reinserted after cleaning. The edge surface is made from a single mould. With many other makes, pores in the edge material and joining surfaces where the edge is joined together often lead to a crack in the edge, which can result in unclean air being sucked into the engine. With paper filters, the air flow rate is significantly lower and decreases further after just a short period of use.In addition, paper filters must be disposed of after the specified mileage. TitanTec sports air filters last a lifetime. This is good for the environment and your wallet.Compared to TitanTec sports air filters, other washable cotton filters only filter much larger particles. Cleaning the filters:A TitanTec sports air filter has no oil residue and has 100% of its original performance again after cleaning.Cleaning is quick and easy.We recommend cleaning after 15,000-20,000 kilometres or once a year at the latest.The best time to clean the air filter is around the end of May or beginning of June, i.e. after the pollen count, as this is the time when the air filter is under the most strain.Under no circumstances should aggressive cleaning agents such as petroleum ether, cleaning petrol, brake cleaner etc. be used, as this can damage the material. Details: 1x set of panel filters (right/left) Length: 264 mm Width: 215 mm Compatible vehicles:BMW M5 (F90) 600 hp, 441 kW, 09/17 to 06/23 BMW M5 (F90) M5 Competition, 625 hp, 460 kW, 07/18 to 06/23 BMW M5 (F90) M5 CS, 635 hp, 467 kW, 03/21 to 02/22 BMW M5 (G90) M5 plug-in hybrid all-wheel drive, 727 hp, 535 kW, from 07/24 BMW M5 Touring (G99) M 5 plug-in hybrid all-wheel drive, 727 hp, 535 kW, from 10/24 BMW M8 Coupe (F92) M8, 600 hp, 441 kW, from 07/19 BMW M8 Coupe (F92) M8 Competition, 625 hp, 460 kW, from 07/19 BMW M8 Gran Coupe (F93) M8, 600 hp, 441 kW, from 11/19 BMW M8 Gran Coupe (F93) M8 Competition, 625 hp, 460 kW, from 11/19 BMW M8 Convertible (F91) M8, 600 hp, 441 kW, from 07/19 BMW M8 Convertible (F91) M8 Competition, 625 hp, 460 kW, from 07/19Note: This is NOT an original BMW product!

Facts: - replaces the main catalytic converter - with 200-cell stainless steel sports catalytic converter - Euro 6 compatible - for non-OPF vehicles - optionally with thermal insulation (with surcharge) - without approval in the area of the StVZO Compatible vehicles:VehicleVehicle typePower outputcubic capacityEngineYear of construction BMW 5 Series (F90)M5 441kW / 600PS4395ccS63 B44 B09.17 - Note: Depending on the software version, the engine control light may light up. We recommend adapting the software in this case.

Facts: - Catless - with thermal insulation - aggressive sound - no excessive noise under normal driving conditions - without approval in the area of the StVZO Compatible vehicles:VehicleVehicle typePowerCapacityEngine typeYear of construction BMW 5 Series (F90)M5 441kW / 600hp4395cm³S63 B44 B09.17 - 11.20 BMW 8 Series (F91/F92/F93)M8 441kW / 600hp4395cm³S63 B44 B09.17 - 11.20 Attention: Not for models manufactured after 11/2020! Note: Depending on the software version, the engine control light may light up. We recommend adapting the software in this case.*ATTENTION: Cat replacement pipes marked “without approval” are not permitted for use on public roads and are intended for racing purposes only! If you nevertheless install a product without approval in your vehicle and use it within the scope of the StVZO, you are liable to prosecution. Possible consequences that you can expect in this case: Expiry of the operating license according to §19 of the StVZO and a possible resulting immobilization of the vehicle. Other possible consequences, such as a charge of tax evasion, as well as possible investigations by the environmental authorities are at the discretion of the investigators.

Facts: - replaces the main catalytic converter - with 4x stainless steel sports catalytic converter - Euro 6 compatible - optionally with Thermo-Integral insulation (with surcharge) - with ECE approval*Compatible vehicles:VehicleVehicle typePower outputEngine capacityEngineYear of construction from BMW 5 Series (F90)M5 441kW / 600PS4395ccS63 B44 B2019 - BMW 5 Series (F90)M5 Competition460kW / 625PS4395ccS63 B44 B2019 - BMW 5 Series (F90)M5 CS467kW / 635PS4395ccS63 B44 B2019 - BMW 8 Series (F92)M8 441kW / 600PS4395ccS63 B44 B2019 - BMW 8 Series (F92)M8 Competition460kW / 625PS4395ccS63 B44 B2019 - BMW X5 (F95)M441kW / 600PS4395ccS63 B44 B2019 - BMW X5 (F95)M Competition460kW / 625PS4395ccS63 B44 B2019 - BMW X6 (F96)M441kW / 600PS4395ccS63 B44 B2019 - BMW X6 (F96)M Competition460kW / 625PS4395cm³S63 B44 B2019 - With combination certificate in conjunction with the Aulitzky Exhaust exhaust system, intercooler, intake and our power increase to 760PS.Note: Depending on the software version, the engine control light may light up. We recommend adapting the software in this case.Suitable for OE article number: 18328088820 Catalytic converter cyl. 1-4 18328088821 Catalytic converter cyl. 5-8 18329504708 Catalytic converter bottom cyl. 1-4 18329504709 Catalytic converter cyl. 5-8 *This downpipe has ECE approval so that it can be used within the scope of the StVZO without registration in the vehicle documents.

Facts: - Exhaust flaps with ceramic bearings - Electric flaps - Plug & Play driveable with original exhaust system - Approval/installation possible in conjunction with our downpipe - Cat/OPF back system - Made in Germany (Lake Constance) - with/without ECE approval (depending on choice of flap control)* Compatible vehicles:VehicleTypePowerEngine capacityEngineYear of construction BMW 5 Series (F90)M5 441kW / 600hp4395ccS63 B44 B09.17 - BMW 5 Series (F90)M5 Competition460kW / 625hp4395cm³S63 B44 B07.18 - BMW 5 Series (F90)M5 CS467kW / 635hp4395cm³S63 B44 B03.21 - BMW 8 Series (F92)M8 441kW / 600hp4395cm³S63 B44 B07.19 - BMW 8 Series (F92)M8 Competition460kW / 625hp4395cm³S63 B44 B07.19 - *ATTENTION! In conjunction with the standard or ECE flap control system (with type approval), this flap exhaust system has ECE approval so that it can be used legally within the scope of the StVZO without registration in the vehicle documents.The use of flap exhaust systems in conjunction with the race flap control (without approval) is not permitted for use on public roads and is only intended for racing purposes! If you nevertheless install a product without approval in your vehicle and use it within the scope of the StVZO, you are liable to prosecution. Possible consequences that you can expect in this case: Expiry of the operating licence in accordance with §19 of the StVZO and possible resulting immobilisation of the vehicle. Other possible consequences, such as a charge of tax evasion, as well as possible investigations by the environmental authorities are at the discretion of the investigators.

The Aulitzky Exhaust OPF-Deleter module is used to mechanically remove the OPF (gasoline particulate filter) without subsequent software adaptation.It is installed in the engine compartment and can be removed at any time without leaving any residue. - No error messages from the module - No detection possible using the manufacturers test device Notes:An OPF deleter is only there to suppress an error message from the catalytic converter or OPF monitoring.  This can appear if, for example, a modified downpipe or an export flap control is installed and the flaps are permanently open as a result.Caution:The OPF must still be installed.However, if the OPF is removed completely, the OPF offset cables are required in addition to the OPF deleter. (These are also available in the online store).1. after removing the OPF, the complete sensor system including all lines must still be connected to the exhaust system and be tight! Otherwise there will be error messages despite the OPF deleter and offset cable!2. for F8X M models, the package consisting of OPF deleter and OPF offset must be purchased from the outset when installing an export flap control system, otherwise error messages may still occur despite the OPF being installed! Compatible vehicles:VehicleVehicle typePowerEngine capacityEngine typeYear of constructionBMW 5er (F90)M5 441kW / 600hp4395cm³S63 B44 B06.21 - BMW 5er (F90)M5 Competition460kW / 625hp4395cm³S63 B44 B06.21 - BMW 5er (F90)M5 CS467kW / 635hp4395cm³S63 B44 B06.21 - Note: This product is NOT approved in the StVZO and is NOT intended for sale within the EU! This article is intended exclusively for show and motorsport purposes and must not be used/installed on public roads. If the component is installed on/in the vehicle, the operating license expires! For dealers only. No sale to end customers!

Function:- variable flap control of the original or retrofitted flap exhaust system- controllable via steering wheel buttons Compatible vehicles: VehicleTypePowerEngine capacityEngine typeYear of constructionBMW 5er (F90)M5 441kW / 600hp4395cm³S63 B44 B09.17 - BMW 5er (F90)M5 Competition460kW / 625hp4395cm³S63 B44 B07.18 - BMW 5er (F90)M5 CS467kW / 635hp4395cm³S63 B44 B03.21 - Note: This product is NOT StVZO approved and NOT intended for sale within the EU! This item is for show & motorsport purposes only and must not be used/installed on public roads. If the component is installed on/in the vehicle, the operating license expires! The pictures shown are examples.

Transform your F9X into a high-performance powerhouse with the BlackBoost cooling air intake system. Experience more power, style and driving dynamics with this premium upgrade. In the world of performance modifications, the airbox is one of the most important engine components you should upgrade. The factory airbox is very restrictive in terms of airflow and filter area. Our cooling air intakes are designed and engineered to overcome these factory restrictions and deliver the maximum airflow with the lowest possible temperatures given the space available. The BlackBoost Cold Air Intakes are designed to be flush with the bonnet of the vehicle and ensure a consistent seal with the rubber seals of the airbox, whilst also ensuring a large surface area for our 10.92cm (4.3 inch) Twin Flow Conical Filters to work properly. The BlackBoost Twin Flow filters have been specifically designed to maximise airflow and surface area. With a diameter of 10.92 cm (4.3 inches) and a height of 20.32 cm (8 inches), they are guaranteed to provide the best airflow and protection. The airboxes are laser-cut aluminium panels with highly complex CNC bends, assembled with stainless steel fasteners and finished with a high-quality black powder coating. The BlackBoost intake kit is a plug-and-play solution that works perfectly without further customisation and requires no additional software tuning. It also works smoothly in combination with turbo upgrades, downpipes, methanol injections etc. to unleash the necessary airflow and utilise the full capacity of the machine for those aiming for 1000+ WHP figures. Scope of delivery:- Powder coated airbox- 2x 10.92 cm (4.3 inch) twin high flow dry filters- 2x BlackBoost CFD developed filter adapters Key features:- Proven power increase from 8 to 30+ hp on production vehicles- Improved responsiveness across the entire rev range- Optimised airflow and increased volume range compared to standard equipment- Increased surface area of the filter elements- Can support airflow for 1000+ WHP configurations- Larger filter element surface area compared to OEM- Plug-and-play bolt-on installation- No ECU tuning required Compatible vehicles: BMW M5 (F90) 441kW/600hp 4395cm³ S63B44B (2017+) BMW M5 (F90) Competition 460kW/625hp 4395cm³ S63B44B (2017+) BMW M5 (F90) CS 467kW/635hp 4395cm³ S63B44B (2017+) BMW M8 (F91/F92/F93) 441kW/600hp 4395cm³ S63B44B (2019+) BMW M8 (F91/F92/F93) Competition 460kW/625hp 4395cm³ S63B44B (2019+)

Cold Air Intake System by BlackBoost. Precision-engineered performance upgrade for BMW M5 (F90) S63 4.4L V8 Twin-Turbo.

A high-end kit for a high-end car. The new F90 gets a new, innovative look. The new AERO body kit from 3DDesign for the F90 fits seamlessly into the familiar, discreetly aggressive race style of the 3DDesign lines. The iconic design is complemented by a perfect fit and the usual uncompromising quality. The real eye-catcher and centerpiece of the body kit - an carbon diffuser that is uncompromisingly and aggressively designed as a direct replacement part. The clear lines and curved shape fit perfectly into the image of the F90. Three inner fins not only ensure a racy look, but also optimum airflow. The F90 M5 carbon diffuser comes in two parts and can also be purchased separately. A performance diffuser for the F90, which is also a real visual upgrade! Pure luxury! Compatible vehicles:BMW 5 (G30, F90) M5 2017-2023BMW 5 (G30, F90) M5 Competition 2018-2023

Dry Carbon Competition diffuser for the rear center diffuser of the F90. Designed to mount directly to the factory lower mounting position for quick and easy installation. The rear diffuser features durable and precise plastic mounting positions and is manufactured using autoclave technology for ultimate lightweight, high durability and precise fitment. Compatible vehicles:BMW 5 (G30, F90) M5 2017-2023BMW 5 (G30, F90) M5 Competition 2018-2023

A high-end kit for a high-end car. The new F90 gets a new, innovative look. The new AERO body kit from 3DDesign for the F90 fits seamlessly into the familiar, discreetly aggressive racing style of the 3DDesign lines. The iconic design is complemented by a perfect fit and the usual uncompromising quality. As with the F10, the front lip comes with a maximum amount of carbon fibre. Above the aggressive centreboard with aero lift slits, the lip extends into the air intakes on the right and left. A performance front lip for the F90 that is also a real visual upgrade! Pure luxury! Compatible vehicles:BMW 5 (G30, F90) 518 d 2018-2020BMW 5 (G30, F90) 518 d mild hybrid 2020-2023BMW 5 (G30, F90) 520 d 2016-2023BMW 5 (G30, F90) 520 d Mild-Hybrid 2019-2023BMW 5 (G30, F90) 520 d Mild-Hybrid xDrive 2019-2023BMW 5 (G30, F90) 520 d xDrive 2016-2023BMW 5 (G30, F90) 520 i 2017-2023BMW 5 (G30, F90) 520 i Mild-Hybrid 2020-2023BMW 5 (G30, F90) 525 d 2017-2019BMW 5 (G30, F90) 530 d 2016-2020BMW 5 (G30, F90) 530 d Mild-Hybrid 2020-2023BMW 5 (G30, F90) 530 d Mild-Hybrid xDrive 2020-2023BMW 5 (G30, F90) 530 d xDrive 2016-2020BMW 5 (G30, F90) 530 e Plug-in Hybrid 2017-2023BMW 5 (G30, F90) 530 e Plug-in Hybrid xDrive 2017-2023BMW 5 (G30, F90) 530 i 2016-2020BMW 5 (G30, F90) 530 i Mild-Hybrid 2020-2023BMW 5 (G30, F90) 530 i Mild-Hybrid xDrive 2020-2023BMW 5 (G30, F90) 530 i xDrive 2016-2023BMW 5 (G30, F90) 540 d Mild-Hybrid xDrive 2020-2023BMW 5 (G30, F90) 540 d xDrive 2017-2020BMW 5 (G30, F90) 540 i 2016-2020BMW 5 (G30, F90) 540 i Mild-Hybrid 2020-2023BMW 5 (G30, F90) 540 i Mild-Hybrid xDrive 2020-2023BMW 5 (G30, F90) 540 i xDrive 2016-2020BMW 5 (G30, F90) 545 e Plug-in Hybrid xDrive 2020-2023BMW 5 (G30, F90) M 550 d xDrive 2017-2020BMW 5 (G30, F90) M 550 i xDrive 2017-2023BMW 5 (G30, F90) M5 2017-2023BMW 5 (G30, F90) M5 Competition 2018-2023

AutoTecknic's vision is to develop the most advanced, innovative and unique products on the market to meet the needs of the most demanding customers. The lightweight carbon fiber aerodynamic products are uniquely designed to enhance the original design of your vehicle. The central design philosophy "understand functional elegance" takes the sporty appearance of your vehicle to a new level. Quality products characterize the AutoTecknic brand. Every single part must pass strict quality controls before it reaches your vehicle. Customers expect nothing less than the best parts from AutoTecknic, so naturally we expect nothing less. AutoTecknic's autoclaved pre-preg carbon fiber structure gives the product superior stiffness, strength and durability compared to traditional handmade carbon fiber composites. AutoTecknic Dry Carbon Center Front Lip for the F90 is both highly visible and highly functional. Compatible vehicles:BMW 5 (G30, F90) M5 2017-2023BMW 5 (G30, F90) M5 Competition 2018-2023

Dry Carbon Performante Aero Splitter for the F90. Designed to seamlessly follow the curvature and mount directly onto the lower bumper mount for quick and easy installation. The Dry Carbon Aero Splitters are manufactured using signature autoclave technology with pre-preg 3K twill carbon fibre and finished with UV protected high gloss clear coat for the ultimate lightweight, durable and snug fitting splitters. The name Dry Carbon comes from the manufacturing process. Dry Carbon is formed by using a pre-preg or impregnated piece of carbon material. This piece of carbon is first placed in a mould and then placed in a sealed vacuum (autoclave) to cure properly. This particular method creates the least amount of waste and forms a lighter version of carbon than the wet method. The autoclave vacuum process for producing dry carbon means that fewer pinholes and virtually no air pockets form in the carbon. Dry carbon is the highest quality version of carbon products produced. AutoTecknic Dry Carbon Performante Aero Splitters are both highly visible and highly functional. Compatible vehicles:BMW 5 (G30, F90) M5 2017-2023BMW 5 (G30, F90) M5 Competition 2018-2023

Facts: Acceleration time: 60-130mph Reduced by 0.22 seconds Max. Flow rate per airbox at 28? H2O: Standard 620 CFM, Eventuri 736 CFM Material: Carbon Manufacturer: Eventuri Parts certificate: A certificate is available for this product for certain regions and vehicles (details below) The F90 Eventuri intake system has been developed through extensive real-world testing and airflow simulation analyses. Now in the updated V2 design, it features sealed filter housings to maintain a more stable IAT even when stationary. The new covers that seal the housings, in conjunction with our blade and shield combination, provide unrestricted airflow while maintaining low IATs through cold air saturation. Our large front air scoops channel ambient air directly into the intake area, ensuring that the engine does not suffer from heat soak. In addition, our gold-coloured, heat-reflecting shields have integrated flow guides that direct the ambient air from the blades into the filters. We have also managed to increase the cross-sectional area of the inlet pipe by over 30% compared to the standard inlet, as it passes through the openings in the struts. The Eventuri difference The F90 Eventuri system uses our patented carbon fibre housings with our bespoke Gen 2 filters, providing an aerodynamically efficient airflow path from the filter to the turbos. Not just another cone filter with a heat shield, but a unique design that creates the Venturi effect and maintains laminar flow conditions to reduce turbo drag. Internal volume Another important design feature of the inlet housings is the internal volume of the tubes as they pass through the struts. On the F90, the airbox system must pass through an oval opening in the strut brace on each side before reaching the turbo inlets. We have managed to increase the internal size of our inlets at this junction, resulting in more available volume for the turbos and therefore less restriction. The increase in cross-sectional area between the Eventuri and the standard airbox is 31% as follows: Inner cross-sectional area of the intake pipe at the strut brace: Standard airbox pipe = 6487 mm² Eventuri intake pipe = 8497 mm² Each intake system consists of: 2 x carbon fibre venturi housings with integrated pipes 2 x customised high-performance Generation 2 filters 2 x carbon fibre filter covers 2 x aluminium intake covers 2 x carbon fibre air scoops 2 x laser-cut heat shields, lined with gold heat reflective material 2 x laser-cut air ramps integrated into the heat shields High-quality silicone couplings and OEM hose clamps Parts certificate The manufacturer's specifications apply for installation. An existing certificate is no guarantee that the product can also be installed in the corresponding vehicle. A certificate is available for this product for the following regions and vehicles: * DE/AT: Vehicle registration document, field K --- CH/LI: Vehicle licence, field 24 Country Model Type approval* DE/AT BMW M5 e1*2007/46*1828*.. DE/AT BMW M5 Competition e1*2007/46*1828*.. DE/AT BMW M8 e1*2007/46*2019*.. DE/AT BMW M8 Competition e1*2007/46*2019*.. Compatible vehicles:VehicleTypePowerEngine capacityEngine typeYear of construction BMW 5 Series (F90)M5 441kW / 600hp4395cm³S63 B44 B09.17 - BMW 8 Series (F91/F92/F93)M8 441kW / 600hp4395cm³S63 B44 B07.19 -

The intercooler for F90 and F92 knows how to impress and will certainly not disappoint you. ColourThe intercooler comes in a classic, appealing black that matches any vehicle colour and rounds off the overall appearance of your car. InstallationThe installation of our intercooler is as simple as the original part. It's a direct replacement, which means you don't have to follow complicated instructions or buy additional parts. MaterialThe intercooler is made of robust and durable aluminium. This material is lightweight yet highly resistant to high temperatures, making it ideal for the requirements of an intercooler. Compatible vehicles:BMW 5 (G30, F90) M5 2017-2023BMW 5 (G30, F90) M5 CS 2021-2022BMW 5 (G30, F90) M5 Competition 2018-2023BMW 8 Convertible (G14, F91) M8 since 2019BMW 8 Convertible (G14, F91) M8 Competition Since 2019BMW 8 Coupe (G15, F92) M8 Since 2019BMW 8 Coupe (G15, F92) M8 Competition Since 2019BMW 8 Gran Coupe (G16, F93) M8 Since 2019BMW 8 Gran Coupe (G16, F93) M8 Competition Since 2019

KW V4 coilover suspension - State of the Art With the new KW V4 with its stainless steel or aluminium coilover struts, you give your super sports car the necessary reserves to further increase the driving dynamics. The three-way adjustable high-performance dampers with their independent adjustment of the rebound, low-speed and high-speed compression damping are based on the successful racing technology of the multiple overall winner of the ADAC Zurich 24h Race Nürburgring and, depending on the vehicle-specific version, have aluminium support bearings. The new KW V4 is developed exclusively for selected high-performance vehicles, which can be moved more safely at the limits of driving dynamics thanks to our KW suspension technology. - 3-way adjustable high-performance dampers with stainless steel coilover struts - Separate and independent damper adjustment in: - Rebound damping with 16 exact clicks + (firmer) / - (more comfortable) - Low-speed compression damping with 6 exact clicks + (firmer) / - (more comfortable) - High-speed compression damping with 14 exact clicks + (firmer) / - (more comfortable) - Two basic set-ups ex works with comfort setting and performance setting - Depending on the vehicle, aluminium support bearings are an integral part of the scope of delivery Please note the conditions and instructions for this product: - VA + HA height-adjustable (coilover struts) - Dampers have easy-to-use adjustment wheels. Due to the design, the rebound stage can only be adjusted when the piston rod is accessible. - Vehicles with electronic damper control must be decommissioned. Electronics kit for decommissioning is included in the scope of delivery for the “YES” article variant. - Variant 4 / Variant 5 Suspension struts / dampers made of aluminium or combined on each axle made of aluminium and stainless steel Technical information: Lowering VA/HA (mm): 15-30/10-30 Design: V4 Adjustable rebound and compression damping Material: Aluminium Adjustment VA/HA: thread/thread Approval: Parts certificate (§19.3) Compatible vehicles: Manufacturer Model Version Body Fuel Performance Displacement Cylinder Drive BMW 5 Series (G30, F90) F5LM, G5L 09/2016- M5 notchback petrol 441 KW 4395 ccm 8 all-wheel drive BMW 5 Series (G30, F90) F5LM, G5L 09/2016- M5 Competition notchback petrol 460 KW 4395 ccm 8 all-wheel drive BMW 5 Series (G30, F90) F5LM, G5L 09/2016- M5 CS notchback petrol 467 KW 4395 ccm 8 all-wheel drive

H&R lowering springs for F90 models from 2018 (VA20-30/HA20-30mm) H&R sports spring kits are the ideal solution if you want to optimize the handling of your vehicle and achieve a sporty look while maintaining the standard driving comfort. Details:Lowering VA/HA Sedan: 30/30mmLowering VA/HA Competition Sedan: 20/20mmSuspension: for vehicles with electric damper controlType of approval: with general operating permit (ABE) Product advantages:Sporty look and performanceLowering of the vehicle's center of gravityLinear or progressive suspension characteristicsCan be combined with standard or retrofit dampersOptimized driving dynamicsSurface protection through powder coatingMade in Germany Compatible vehicles:BMW M5 Sedan F90 type F5LM only with adaptive damper control 2018- front axle 30mm / rear axle 30mmBMW M5 Competition Sedan F90 type F5LM, only with adaptive damper control 2018- front axle 20mm / rear axle 20mm

Eibach Pro-Kit performance suspension springs for front and rear axle E10-20-041-01-22 The Eibach Pro-Kit lowering springs are the ideal solution for your vehicle, as the kit lowers the centre of gravity, reduces rebound when accelerating, reduces body roll when cornering and dips when braking. As a result, understeer and oversteer no longer occur. Lowering the vehicle with the Pro-Kit springs reduces the standard distance between the tyres and the wheel arch and gives the vehicle a sporty look. In addition, the handling of the vehicle is maximised. The Eibach Pro-Kits are designed by Eibach suspension engineers and testing experts to deliver a combination of sporty looks and performance without compromising on safety or ride quality. - Developed and tested for combination with standard and aftermarket dampers- Component of the Eibach Pro system- Top performance handling- Lowers the vehicle's centre of gravity by up to 40 mm (depending on the vehicle)- Spring design for traction and attraction- Progressive suspension characteristics- Performance handling- ABE or parts certificate Note: Only for vehicles without levelling control. Information:- Lowering front axle: approx. 25mm- Lowering rear axle: approx. 20mm- Type of approval: with expert opinion- Illustration may differ from the original Compatible vehicles:- Axle load front axle: up to 1215kg- Axle load rear axle: up to 1260kg- EC type approval number: e1*2007/46*1688*..- Only for vehicles without levelling system BMW 5 (F90) M5 441kW / 600PS 7909-ABWBMW 5 (F90) M5 Competition 460kW / 625hp 7909-ABV

The RKP carbon mirror caps for the F90 are definitely a highlight on your vehicle.They impress with their perfect fit and easy installation. Details:- Flawless fit- Extremely light- Clear lacquered and high-gloss polished Compatible vehicles:BMW M5 441kW/600PSBMW M5 Competition 460kW/625PS

The exterior mirror covers in glossy pre-preg carbon fibre give your standard mirror units a more aggressive and premium look.Quick and easy to fit, they are a styling option with perfect value for money to enhance the road presence of your vehicle. Unlike normal carbon fibre, pre-preg carbon is reinforced to increase strength and durability. It can also be a staggering 70% lighter than other carbon fibre options.Prepreg carbon is far more uniform than other carbon types, meaning the likelihood of imperfections is drastically reduced. The manufacturing process eliminates unwanted air bubbles and results in a perfectly smooth and high-gloss finish. Details:- 100% pure prepreg carbon fibre construction- OEM-style weave- High gloss finish- Guaranteed fit- registration free Scope of delivery:- 1x pair of mirror caps Compatible vehicles:BMW F90 M5 SaloonBMW F91 M8 ConvertibleBMW F92 M8 CoupeBMW F93 M8 Gran Coupé Note: This is NOT an original BMW product!

Facts:- Plug & Play installation using illustrated installation instructions- Special wiring harness for your vehicle- High-quality electronics “Made In Germany”- Electronic components with product qualification for motor vehicles according to AEC-Q100 installed- Support from us as co-developer and manufacturer Scope of delivery:The scope of delivery includes the motorsport add-on module, an engine-specific wiring harness, illustrated installation instructions in DE/EN and a BYPASS connector, which you can use to restore your vehicle to series production. Compatible vehicles: VehicleVehicle typePowerEngine capacityEngine typeYear of constructionBMW 5er (F90)M5 CS467kW / 635hp4395cm³S63 B44 B03.21 - LEGAL INFORMATION: THE INSTALLATION OF ADDITIONAL ELECTRONICS IS A STRUCTURAL MODIFICATION TO THE MANUFACTURER'S ELECTRONICS. WITHOUT REGISTRATION IN THE VEHICLE DOCUMENTS BY MEANS OF AN INDIVIDUAL CERTIFICATE FROM TÜV; DEKRA OR OTHER RECOGNIZED TESTING INSTITUTES, THE INSTALLATION WILL INVALIDATE THE OPERATING LICENSE. IF USED ON PUBLIC ROADS, THIS WILL RESULT IN THE LOSS OF INSURANCE COVER. WE DO NOT CURRENTLY HAVE A PARTS CERTIFICATE FOR YOUR VEHICLE. THEREFORE, THIS SYSTEM IS EXCLUSIVELY SUITABLE FOR MOTORSPORT. ATTENTION: IF YOU USE THE ADDITIONAL ELECTRONICS, YOU MAY LOSE YOUR WARRANTY CLAIMS AGAINST THE SELLER OR WARRANTY CLAIMS AGAINST THE MANUFACTURER. IF YOU HAVE ANY FURTHER QUESTIONS, PLEASE DO NOT HESITATE TO CONTACT US!

Compatible vehicles:BMW F90 M5 441KW/600hp (2017+)BMW F90 M5 Competition 460KW/625hp (2018+)BMW F90 M5 CS 467KW/635hp (2021+)BMW F91/92/93 M8 441KW/600hp (2019+) Boost your model's performance to a new level with the Wagner Tuning high-performance intercooler! The 4.4-litre V8 biturbo engine (S63 B44T4) has an indirect charge air cooling circuit in which the charge air is cooled by a water-cooled charge air cooler. With our innovative high-performance intercooler from Wagner Tuning, you can replace the original intercooler and experience an impressive increase in performance. Our high-performance intercooler has a new type of performance mesh with dimensions of 192 mm x 156 mm x 128 mm. It has been specially developed for the high demands of the engine and offers an incredible 75 % more external mesh volume compared to the standard intercooler. The optimised ratio between the inner and outer cooling surface ensures maximum heat transfer and optimum internal airflow. The cast aluminium end boxes were designed using the latest CAD technology and optimised using CFD simulations. The result is outstanding cooling properties with minimal back pressure, ensuring optimum cooling of the supercharged air with a significant increase in performance. This kit is ideally suited even for demanding racing. To ensure a long-lasting cooling effect, all Wagner Tuning intercoolers are equipped with a thermally conductive anti-corrosion coating. Installation of the system is uncomplicated thanks to our detailed installation instructions and is carried out in plug & play style. Advantages:- Significantly improved cooling performance- More power and torque for your engine- Mechanical relief of the turbocharger- Additional WMI ports- 100 % pressure resistance- 100 % plug-and-play- Up to 4 years warranty Mains dimensions OEM intercooler:152 mm x 143 mm x 100 mmV = 2.19 litres Mains dimensions Wagner Tuning intercooler:192 mm x 156 mm x 128 mmV = 3.83 litres (+75%) Scope of delivery:2 intercoolers5 silicone air hoses1 mounting material Attention: Not authorised in the area of the StVZO.

The certificate includes the increase in rated power to 227-326kW/309-443PS (depending on the vehicle and hardware installed).Note: The purchase of the performance upgrade does not include registration in the vehicle documents. This must be purchased separately.To get the maximum performance from your vehicle, we recommend filling up with premium fuel (100/102 octane) before and after the optimisation. The following hardware components may also be installed individually or in combination for all listed vehicles as part of our combination certificate: - HJS downpipe- Wagner Tuning intercooler- Wagner Tuning intake system- Wagner Tuning pressure pipes- Aulitzky exhaust systemIn combination with all the hardware, a legal stationary noise increase to 102dB is possible. Compatible vehicles:VehicleTypePower outputEngine capacityEngineNew rated powerNote Audi A3 (8YA/8YS)S3 quattro228kW / 310PS1984cm³DNFB1) 281kW (382PS)2) 326kW (443PS)optionally in conjunction with the standard or Aulitzky exhaust system Audi Q3 (F3B/F3N)45 TFSI quattro180kW / 245PS1984cm³DNPA1) 227kW (309PS)2) 253kW (344PS)only in conjunction with the standard exhaust system Audi TT (FV3/FV9)45 TFSI / quattro180kW / 245PS1984cm³DNPA1) 227kW (309PS)2) 253kW (344PS)optionally in conjunction with the standard or Aulitzky exhaust system Audi TT (FV3/FV9)TTS quattro235kW / 320PS1984cm³DNFG1) 281kW (382PS)2) 326kW (443PS)optionally in conjunction with the standard or Aulitzky exhaust system Cupra Ateca (KH)2.0 TSI 4Drive221kW / 300PS1984cm³DNFC1) 281kW (382PS)2) 326kW (443PS)only in conjunction with the standard exhaust system Cupra Leon (KL1/KL8)2.0 TSI180kW / 245PS1984cm³DNPA1) 227kW (309PS)2) 253kW (344PS)optionally in conjunction with the standard or Aulitzky exhaust system Cupra Leon (KL1/KL8)2.0 TSI / 4Drive221kW / 300PS228kW / 310PS1984cm³DNFB, DNFC1) 281kW (382PS)2) 326kW (443PS)optionally in conjunction with the standard or Aulitzky exhaust system Skoda Octavia IV (NX5)RS 2.0 TSI180kW / 245PS1984cm³DNPA1) 227kW (309PS)2) 253kW (344PS)only in conjunction with the standard exhaust system VW Golf VIII (CD1)GTI 2.0 TSI180kW / 245PS1984cm³DNPA1) 227kW (309PS)2) 253kW (344PS)optionally in conjunction with the standard or Aulitzky exhaust system VW Golf VIII (CD1)GTI CS/ED45 2.0 TSI221kW / 300PS1984cm³DNFC1) 281kW (382PS)2) 326kW (443PS)optionally in conjunction with the standard or Aulitzky exhaust system VW Golf VIII (CD1/CDV)R 2.0 TSI 4motion235kW / 320PS245kW / 333PS1984cm³DNFF, DNFG1) 281kW (382PS)2) 326kW (443PS)optionally in conjunction with the standard or Aulitzky exhaust system VW Tiguan (AD1)2.0 TSI180kW / 245PS1984cm³DNPA1) 227kW (309PS)2) 253kW (344PS)only in conjunction with the standard exhaust system VW Tiguan (AD1)R 2.0 TSI 4motion235kW / 320PS1984cm³DNFG1) 281kW (382PS)2) 326kW (443PS)only in conjunction with the standard exhaust system VW T-Roc (A1)R 2.0 TSI 4motion221kW / 300PS1984cm³DNFC1) 281kW (382PS)2) 326kW (443PS)only in conjunction with the standard exhaust system 1) with Wagner Turbo Outlet2) with Wagner Turbo Outlet + HJS downpipe

The G90 rear spoiler made of Pre-Preg carbon fibre gives your vehicle a distinctly sporty aggressiveness and gives it a lot of presence on the road.Details:- Constructed from 100% pure pre-preg carbon fibre- OEM style weave- High-gloss finish- Perfect fit- registration according to §21 possible Scope of delivery:1x ducktail in prepreg carbon Compatible vehicles:BMW M5 G90BMW i5 G60BMW 5 Series G60Note: This is NOT an original BMW product!

Here you get an original TitanTec sports air filter with all its advantages:- higher air flow rate- higher filter performance (even smaller particles are filtered)- The particles are trapped in the filter after intake and thus remain trapped until cleaning.- Washable and reusable filter- Increased air flow and therefore better combustion in the engine- No reduction in air flow over a minimum of 50,000 km- Sufficient air even at high engine speeds- more power- Better intake noise- Reduced fuel consumption Only TitanTec sports air filters use polyurethane as the edge material. Polyurethane is more resistant to petrol, vapours and the like. It has an ideal remoulding. This ensures that the edge of the filter is 100% sealed even when it is reinserted after cleaning. The edge surface is made from a single mould. With many other makes, pores in the edge material and joining surfaces where the edge is joined together often lead to a crack in the edge, which can result in unclean air being sucked into the engine. With paper filters, the air flow rate is significantly lower and decreases further after just a short period of use.In addition, paper filters must be disposed of after the specified mileage. TitanTec sports air filters last a lifetime. This is good for the environment and your wallet.Compared to TitanTec sports air filters, other washable cotton filters only filter much larger particles. Cleaning the filters:A TitanTec sports air filter has no oil residue and has 100% of its original performance again after cleaning.Cleaning is quick and easy.We recommend cleaning after 15,000-20,000 kilometres or once a year at the latest.The best time to clean the air filter is around the end of May or beginning of June, i.e. after the pollen count, as this is the time when the air filter is under the most strain.Under no circumstances should aggressive cleaning agents such as petroleum ether, cleaning petrol, brake cleaner etc. be used, as this can damage the material. Details: 1x set of panel filters (right/left) Length: 264 mm Width: 215 mm Compatible vehicles:BMW M5 (F90) 600 hp, 441 kW, 09/17 to 06/23 BMW M5 (F90) M5 Competition, 625 hp, 460 kW, 07/18 to 06/23 BMW M5 (F90) M5 CS, 635 hp, 467 kW, 03/21 to 02/22 BMW M5 (G90) M5 plug-in hybrid all-wheel drive, 727 hp, 535 kW, from 07/24 BMW M5 Touring (G99) M 5 plug-in hybrid all-wheel drive, 727 hp, 535 kW, from 10/24 BMW M8 Coupe (F92) M8, 600 hp, 441 kW, from 07/19 BMW M8 Coupe (F92) M8 Competition, 625 hp, 460 kW, from 07/19 BMW M8 Gran Coupe (F93) M8, 600 hp, 441 kW, from 11/19 BMW M8 Gran Coupe (F93) M8 Competition, 625 hp, 460 kW, from 11/19 BMW M8 Convertible (F91) M8, 600 hp, 441 kW, from 07/19 BMW M8 Convertible (F91) M8 Competition, 625 hp, 460 kW, from 07/19Note: This is NOT an original BMW product!

The Aulitzky Tuning Portinjection Rail for the S58 engines of the G8x series was developed to meet the high demands of the engine.Compatible vehicles:VehicleVehicle typePowerCapacityEngineYear of construction BMW 2er (G87)M2338kW / 460hp2993cm³S58 B30 A11.22 - BMW 3 Series (G80)M3353kW / 480hp2993cm³S58 B30 B11.20 - BMW 3 Series (G80/G81)M3 Competition / xDrive375kW / 510hp390kW / 530hp2993cm³S58 B30 A05.21 -07.24 - BMW 3 Series (G80)M3 CS xDrive405kW / 551hp2993cm³S58 B30 A03.23 - BMW 4 Series (G82)M4353kW / 480hp2993cm³S58 B30 B11.20 - BMW 4 Series (G82/G83)M4 Competition / M xDrive375kW / 510hp2993cm³S58 B30 A11.20 - BMW 4 Series (G82)M4 CSL xDrive405kW / 551hp412kW / 560hp2993cm³S58 B30 A05.22 - 02.2311.22 - 02.23

Upgrade your Mercedes AMG CLS 63(S) M157 with the BlackBoost Generation 2 high-performance cold air intake system - designed for enthusiasts who crave more power, efficiency and eye-catching aesthetics. State-of-the-art design and durabilityThe airboxes are laser-cut with the utmost precision from high-strength aluminum, assembled with stainless steel fasteners and finished with a sleek black powder coating for durability and a premium look. This robust construction ensures that your intake system performs optimally even under the most demanding conditions. Customized engine coverThe intake system includes a specially designed engine cover that combines style and functionality. Not only does it protect vital components, it also gives your engine bay a classy, elegant look. Two synthetic, dry, high-flow oval air filtersEquipped with newly developed dual oval filters, this system provides a larger surface area for better airflow and filtration. These high-flow filters ensure your engine receives cleaner air, improving overall performance. Molded composite intake manifolds with 1/8 NPT pre-turbo methanol portThis intake system with advanced molded composite manifolds is designed for maximum efficiency. Integrated 1/8 NPT ports allow for easy pre-turbo methanol injection upgrades, lowering intake temperatures and optimizing airflow, especially in high performance scenarios. Oversized intake ports and couplings for maximum performanceThis system includes oversized intake ports that further improve airflow into the intake, better oxygenating the engine and increasing power potential. In addition, oversized, heat-resistant couplings facilitate installation and ensure maximum durability under extreme conditions. Easy plug-and-play installationThis cold air intake system is a direct bolt-on upgrade that requires no fine-tuning or additional modifications. It integrates seamlessly with other performance components such as turbochargers, downpipes and methanol injection systems, making it the perfect choice for CLS 63(S) M157 owners looking for increased performance. Scope of delivery:- Powder-coated airbox with engine cover- Oversized intake ducts- Molded composite intake manifold with 1/8 Npt fittings- Oversized couplings- Vent line connections- Connecting clamps- Oval Twin Flow dry filters- Filter clamps- Extension cable- AMG badge transfer kit Key features:- Completely new design with motor cover- Oval shaped filters for a larger filter surface area- Open/close filter covers for customizable airflow control- 1/8 NPT connections integrated into the composite intake tubes- Proven power increase of 8-30+ hp on stock vehicles- Improved throttle response across the entire rev range- Supports airflow for 1000+ hp configurations- Plug and play installation- No ECU tuning required- No illumination of the check engine light Compatible vehicles:E63 AMG (W212/S212) - M157 5.5L V8 BiTurbo - (2013 - 2016)CLS63 AMG (C218/X218) - M157 5.5L V8 BiTurbo - (2012 - 2018)E500 (W212/S212) - M278 4. 7L V8 BiTurbo - (2013 - 2016)CLS 500 (C218/X218) - M278 4.7L V8 BiTurbo - (2012 - 2018)E550 (W212/S212) - M278 4.7L V8 BiTurbo - (2013 - 2016)CLS 550 (C218/X218) - M278 4.7L V8 BiTurbo - (2012 - 2018)

Facts: Performance increase (standard Golf R): 10-13hp, 12-15Nm Performance increase (tuned Golf R): 15-20hp, 25-30Nm Material: Carbon fibre Manufacturer: Eventuri Parts certificate: A certificate is available for this product for certain regions and vehicles (details below) The MK8 Golf GTi/R intake manifold is a complete revision of the standard intake manifold up to the turbo inlet. Taking inspiration from our RS3 intake, we have maximised the space available to create an intake that is suitable for all power levels, from standard specification through to high performance systems with hybrid or full frame turbos. This intake system has been developed to provide the highest possible flow rate whilst achieving the lowest possible intake temperatures. Each component has been designed to give the turbo a smooth and clear flow path. The restrictive standard intake pipe with a diameter of 73 mm is replaced by an intake pipe with a larger diameter of 94 mm. The filter itself has an outer diameter of 192mm or 7.5? with a filter area of over 110,000mm^2. The patented Venturi housing is designed to provide the largest possible internal volume for the available space in the Golf engine bay and provides laminar flow to the turbo pipe. Finally, the duct seals the filter opening at the windscreen, but is not restricted by the standard intake alone. We have raised the front of the duct to now create an additional opening behind the bonnet, equivalent to an extra 7? diameter hole for the inlet to draw from. The resulting system can significantly outflow the stock airbox while keeping intake temperatures to a minimum with the sealed design. Dyno testing Our MK8 Golf intake has been independently tested by a renowned tuner in the UK, Regal Autosport. A MK8 Golf R was tested in original condition and with a tuning box. The tests were carried out on the same day, with the standard airbox being tested first and then the Eventuri. No other changes were made to the car. The first graph shows the results with a stock map. As can be seen, there is a measurable gain across the rev range of up to 12bhp. This gain is noticeable even in a standard vehicle on the road due to better throttle response and faster acceleration. The second diagram shows the results when using a tuning box that increases the flow requirement of the intake system. The tuning box was used for both the standard airbox and the Eventuri intake, with no changes made between tests. With a higher flow requirement, the stock airbox places a greater restriction on the turbo, which is evident by the significant gain achieved with the Eventuri fitted. We now have a power increase of up to 20 hp and 30 Nm across the entire rev range, which is even more noticeable on the road. We expect the gains to be even greater with higher tuning levels. The improvements are due to a combination of reasons: 1) The closed system keeps IAT levels low - the Golf's engine bay can heat up very quickly, so an open cone filter leads to an increase in IAT levels and therefore a loss of power. 2) The Venturi housing provides a smooth transition from the filter to the intake pipes, both of which are matched to an internal diameter of 94mm. This contributes to a more efficient operation of the turbo. 3) The entire system is made from pure pre-impregnated carbon fibre, which provides excellent insulation against heat and has smooth internal surfaces, unlike glass fibre, which has sharp resin lines. Parts certificate The manufacturer's specifications apply for installation. An existing certificate is no guarantee that the product can also be installed in the corresponding vehicle. A certificate is available for this product for the following regions and vehicles: * DE/AT: Vehicle registration document, field K --- CH/LI: Vehicle licence, field 24 Country Model Type approval* DE/AT Audi S3 (8Y) e1*2007/46*2060*.. DE/AT Audi TTS (FV/FVP/8S e1*2001/116*0369*.. DE/AT Cupra Ateca LCI e9*2007/46*6394*.. DE/AT Cupra Formentor e9*2007/46*4008*.. DE/AT Cupra Leon e9*2007/46*3167*.. DE/AT Skoda Octavia RS e8*2007/46*0355*.. DE/AT Skoda Superb e8*2007/46*0317*.. DE/AT Volkswagen Arteon R e1*2007/46*1725*.. DE/AT Volkswagen Golf 8 GTI e1*2007/46*2014*.. DE/AT Volkswagen Golf 8 GTI CS e1*2007/46*2014*.. DE/AT Volkswagen Golf 8R e1*2007/46*2014*.. DE/AT Volkswagen Tiguan R e1*2001/116*0450*.. DE/AT Volkswagen Tiguan R (AD1) e1*2007/46*0487*.. Compatible vehicles: VehicleVehicle typePowerEngine capacityEngine type Audi A3 (8Y)S3 2.0 TFSI quattro228kW / 310hp1984cm³DNFB Audi Q2 (GA)SQ2 2.0 TFSI quattro221kW / 300hp1984cm³DNFC Cupra Ateca (KH)2.0 TSI 4Drive221kW / 300hp1984cm³DNFC Cupra Leon (KL)2.0 TSI221kW / 300hp228kW / 310hp1984cm³DNFCDNFB Cupra Formentor (KM)2.0 TSI 4Drive228kW / 310hp1984cm³DNFB VW Arteon2.0 TSI 4motionR 2.0 TSI 4motion206kW / 280hp235kW / 320hp1984cm³DNFEDNFG VW Golf 8GTI Clubsport/ED45 2.0 TSI221kW / 300hp1984cm³DNFC VW Golf 8R 2.0 TSI 4motionR 2.0 TSI 4motion 20Years235kW / 320hp245kW / 333hp1984cm³DNFGDNNF VW Passat B8 (3G)2.0 TSI 4motion206kW / 280hp1984cm³DNFE VW T-Roc (A1)2.0 TSI 4motion221kW / 300hp1984cm³DNFC VW Tiguan II (AD)R 2.0 TSI 4motion235kW / 320hp1984cm³DNFG